Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CCDTR73 | NO FUNCTION AT ALL; NO EVF / RESOLDER CN504 ON THE VS125 BD | You hear a beep when changing from VTR mode to camera mode,but no function at all and no EVF. Found bad CN504 on VS125 board. -SOLUTION :Resolder CN504 on VS125.- HQ Comments: CN504 is the connector between the DC to DC converter andthe VS bd. No volt | ||
Sony | CCDTR73 | NO EJECT/ DRUM RAMPS UP/ REPLACE X502 OFF OF IC505 | When powering up unit will spin the drum and stop. No otherfunctions work. After resoldering IC505 same problem. Isolated problemon servo board VC125, and found X502 not oscillating. | ||
Sony | CCDTR70 | UNIT PLAYS WITH NO TAPE INSIDE / RPL PS500 | Unit goes into play with no tape inside also does not sensereel rotation. Found PS500 open | ||
Sony | CCDTR600 | NO FUNCTION AT ALL; NO EVF / RESOLDER CN504 ON THE VS125 BD | You hear a beep when changing from VTR mode to camera mode,but no function at all and no EVF. Found bad CN504 on VS125 board. -SOLUTION :Resolder CN504 on VS125.- HQ Comments: CN504 is the connector between the DC to DC converter andthe VS bd. No volt | ||
Sony | CCDTR600 | NO EJECT/ DRUM RAMPS UP/ REPLACE X502 OFF OF IC505 | When powering up unit will spin the drum and stop. No otherfunctions work. After resoldering IC505 same problem. Isolated problemon servo board VC125, and found X502 not oscillating. | ||
Sony | CCDTR400 | INDIVIDUAL MOTOR TESTING USING RM-95 | Models such as the CCDTR400 and CCDFX430 do not include themotor test on one of the service procedures, ex, capstan forward andreverse drum forward and reverse etc. | ||
Sony | CCDTR400 | UNIT PLAYS WITH NO TAPE INSIDE / RPL PS500 | Unit goes into play with no tape inside also does not sensereel rotation. Found PS500 open | ||
Sony | CCDTR101 | STEADYSHOT JERKED SIDE TO SIDE; ADJUST ADDRESSES 12 & 13 | Steady Shot Jerky | ||
Sony | CCDTR101 | TDK TAPES GET STUCK | Tape stuck in unit won't eject. | ||
Sony | CCDSC5 | NO LCD PLAY / PEPLACE L004 | No LCd operation. Fluorescent tube does light up however,no R5 or B out from IC001 to LCD block PD42 board. | ||
Sony | CCDFX730V | INDIVIDUAL MOTOR TESTING USING RM-95 | Models such as the CCDTR400 and CCDFX430 do not include themotor test on one of the service procedures, ex, capstan forward andreverse drum forward and reverse etc. | ||
Sony | CCDFX730V | BLUE LCD OR MULTI COLORS OR NO VID IN MONITOR/RESOLDER | Had a blue screen and color charged when I flexed board. -SOLUTION :Re soldered and cleaned IC002 RGB decoder. | ||
Sony | CCDFX710 | NO VIDEO IN CAMERA MODE | In camera mode no video in viewfinder and no video on videoout. Also data in viewfinder would roll. | ||
Sony | CCDFX630 | WHEN EJECT TAPE GUIDES UNLOAD HALFWAY THEN LOAD/PS500 ON VS1 | Trying to eject tape guides would come back halfway then loadagain. Both in VTR and camera. Also when in VTR you could hit play andunit would think there was a tape in mech. | ||
Sony | CCCTR83 | NO EJECT/ DRUM RAMPS UP/ REPLACE X502 OFF OF IC505 | When powering up unit will spin the drum and stop. No otherfunctions work. After resoldering IC505 same problem. Isolated problemon servo board VC125, and found X502 not oscillating. |