Dicas Reparação
Modelo - Chassis CCDFX710
Pesquisa: CCDFX710 Enviar Dica Resolvida
Resultados 21
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CCDFX710 | UNIT DEAD, F950 OPENS (EDGE OF BRACKET SHORTED TO FP607) | Unit would intermittently go dead, F950 would open. Afterreplacing F950, unit would work OK again for a while, then F950 would blowagain. Also found this problem on serial number 1010139. | ||
| Sony | CCDFX710 | EDIT SEARCH VIDEO DISTORTION (CAPSTAN MOUNT SCREW WAS LOOSE) | Customer complaint of int. distorted video on edit search.Also mechanism noisy. Had excessive intermittent tracking lines. Editsearch virtually unuseable. -SOLUTION Found mounting screw for capstan motor loose causing capstanto change position in edit | ||
| Sony | CCDFX710 | NO VIDEO IN CAMERA MODE | In camera mode no video in viewfinder and no video on videoout. Also data in viewfinder would roll. | ||
| Sony | CCDFX710 | NO RECORD VIDEO, PLAY OK/R159 OPEN | Playback video OK. Record video nothing, just snow. | ||
| Sony | CCDFX710 | NO AUDIO PLAYBACK OR E TO E/CHECK R508 | No audio playback or E to E. | ||
| Sony | CCDFX710 | HORIZONTAL DISTORTION IN CAMERA VIDEO/REPLACE X801 | An inch thick horizontal noise bar on screen. Camera E to Evideo. | ||
| Sony | CCDFX710 | UNIT CUTS OUT WHEN SUPERIMPOSE MEMORY BUTTON PRESSED/IC506 | When depressing memory button for super impose function, theentire unit cuts out for a brief period of approx. 2 seconds. | ||
| Sony | CCDFX710 | LCD DISPLAY PROBLEMS/RESOLDER CN512 | LCD display intermittent or doesn't show all characters. | ||
| Sony | CCDFX710 | REMAINING TAPE LENGTH INDICATOR/RESOLDER SL-24 BOARD | Tape length display would show last segment only and thendisplay zero min. Tape Icon would flash. This would happen no matter howmuch tape was on take-up reel. Unit never shut down due to lack of reelFG. | ||
| Sony | CCDFX710 | CN512 CAUSES NO OR INTERMITTENT LCD DISPLAY/SEE SB#343 | Intermittent or no LCD display and functions e.g., date,exposure, shutter etc. | ||
| Sony | CCDFX710 | CCDFX710 SERVICE BULLETIN CSV-3 #328 | VTR/Camera power slide witch breaks, when attempting to pullswitch base assy vertically (Seg S.B. #328). There is a lip on the basewhich gets in the way. | ||
| Sony | CCDFX710 | LCD DISPLAY SHOWING ALL "ONES" | A bad connection on CN510 caused the LCD display to displayall ones. Re soldering corrected condition. -HQ COMMENTS: CN510 carries key matrix information to the VK-23 board. | ||
| Sony | CCDFX710 | NO BEEP/BAD FEED-THRU ON CS-33 | Customer complained of no beep. This was caused by bad feedthroughs in the area of the board where the label(not the part) Q576appears. Please note the poor board separation points, from production. Inaddition I am seeing many instances of connectors, re | ||
| Sony | CCDFX710 | NO RECORD PLAYBACK OK/REPLACE IC501 | Upon playback of recorded signal there was no picture orcounter. A pre-recorded tape played back O.K. | ||
| Sony | CCDFX710 | KEEPS BLOWING F-950/CHECK INSULATION AROUND VF CABLE | The unit blows F-950. With the cabinet off the units willplay fine. Replacing cabinet fuse will blow. 7 wire from the view finderto the main board was shorting. Insulated wires and unit appears to workfine.Connector cable is not available through par |