Dicas Reparação
Modelo - Chassis
Pesquisa: Enviar Dica Resolvida
Resultados 81408
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | WMF200 | PROBLEM FIX - AUDIO OUTPUT LEVEL IS LOW | Found low audio output (Cassette). Found audio input existsat R-112/212 and amplification exists at R-113/213. | ||
| Sony | D66 | 1/2 VCC ADJUSTMENT POINTS | Manual does not give location of 1/2 Vcc point for adjustment. | ||
| Sony | CCDV99 | NO PICTURE ON PAUSE | When camera is in playback, put in pause, video will be lost(bad A head). Following the video path, found pin 20 HD-8 board hadone field missing when put in pause. Following it back, found that inpause, video switch between pin 5 and 3 IC-202 on the H | ||
| Sony | CCDTR5 | NO VIDEO OUT OF CAMERA | Connections on inner side of CN-301 on CD-14 board were bad.Voltage was on connector not on imager IC. | ||
| Sony | KV27XBR10 | PICTURE COMES ON SLOW AND FLASHES FOR FIVE MINUTES, | On first turn on, the picture or screen will come on veryslowly. When picture comes on, it will flash on and off until the set ison for five minutes. Unit will work well. This set has always done this. | ||
| Sony | SPP110 | FRONT CABINET'S CLIPS OF THE HANDSET ARE BROKEN | Unit comes to the SSC with loosened cabinet at the batterycompartment due to the broken clips. The front cabinet can be repairedinstead of replacing it. | ||
| Sony | WMF707 | AUTOMATIC SCAN NOT LOCKING | When changing frequency range of tuner from Japanese toAmerican, according to Customer Information, the tuner feature of lockingonto strong station signals is lost. When reverting back to Japanesefrequency range, the tuner will lock onto strong signals | ||
| Sony | CCDF45 | MECHANISM WILL NOT FUNCTION | Mechanism will not function. Pins 18, 17, 16 and 15 of IC-501minimum data was not changing. No output just 5VDC. | ||
| Sony | CDX7580 | PART NUMBER FOR FEED GUIDE MISSING | Part number for feed guide missing from manual. Part ispictured on page 40 of manual, connected to FOP (Ref. No. 926) by screws437 and 436. Kansas City researched this and the correct part number islisted above. -HQ COMMENTS: Thanks for researching th | ||
| Sony | KV2675R | REMOTE CONTROL WORKS INTERMITTENTLY, C-609, RY-601, THP-601 | Customer complaint was that remote control was workingintermittently. When diagnosed, the remote would work at approximately 90degrees in either direction of the receiving eye. The relay alsochattered causing the set to come on and go back off again, w | ||
| Sony | KV32XBR10 | CONTINUATION OF FPR L1613 | |||
| Sony | KV32XBR10 | AT TURN ON - BLANKS IN THREE QUICK BLINKS | At turn on blanks in three quick blinks, then works ok.Experience with other ANU-1 chassis suggests the problem will get worseand will blank for extended periods of time. Changing the CRT willcorrect the problem. Interchanging CRTs from two sets with t | ||
| Sony | XR6500 | NO AUDIO ON AM OR FM | Dolby IC had input signal but no output. | ||
| Sony | STRAV1020 | SERVICE MANUAL CORRECTION | The schematic is incorrect. It shows IC-701 reversed, pins1-15 are shown in the wrong sequence. The voltages on 1-15 are correct asshown in schematic with the exception of B+ and B-. Example: on PCB C702and R702 actually connect to pin 15, on schemati | ||
| Sony | GV8 | WRONG SUBSTITUTE FOR IC101 (SV-34) | When the above part number is keyed in the parts system, itsubstitutes to 8-752-809-34, which is a CXP5058H-200Q. Is this a goodpart substitution? RPC gives us the same sub number. The servicer claimsthe new IC does not work. Can you please advise? |