Dicas Reparação
Modelo - Chassis KV32XBR10
Pesquisa: KV32XBR10 Enviar Dica Resolvida
Resultados 53
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | KV32XBR100 DA1 | RETRACE LINES | KV32XBR100 Unit has a bright screen with retrace lines | The 200 vdc line at the CRT is only running at 144 vdc on all cathodes. Unit has an open diode on flyback transformer for the 200 vdc source | Muller |
| Sony | KV32XBR100 DA1 | raster | Unit will not get raster even if the G2 is raised all the way up. We still don't get a bright screen with retrace lines. Tech requesting the Feature Box. This will be a waste of time because the feature box is not necessary | R554 was open | Muller |
| Sony | KV32XBR10 ANU1 | no audio | KV32XBR10 Unit has no audio | Product has a defective MTS audio controller part # 8-741592-2 (8-741-100-56) original number SBX1592-02 corrected the symptom | Muller |
| Sony | KV32XBR10 ANU1 | AUDIO | Unit has no audio | 8-741-592-2 (8-741-100-56) original number SBX1592-02 corrected the symptom | Muller |
| Sony | KV32XBR100 | 36 PIN MULTI CABLE P/N , 1775-534-11 | Need the part number for the 36 multi pin cable between theFeature box (tuner) and the monitor.SOLUTION: The part number is listed in the SM under Accessories andPacking Materials: The description is incorrect. It is listed as: CableAss'y (Half Pitch | ||
| Sony | KV32XBR100 | INCOMPLETE MENU SCREEN, X BOARD | No channel display in screen and missing icons in left handside menu. Found X board popped out from PCB support clip and is causingpoor connection between CN5002 (X board) and CN7001 (A board).See servicee manual page 76 component side matrix A:1. S/N | ||
| Sony | KV32XBR100 | PART NUMBER FOR THE 50O EXTENSION CABLE, 1-900-800-86 | On page 12 of the Service Manual a 50p extension cable isshown between the AB and X board. There is no part number in theservice manual for this extension cable. -HQ COMMENTS: The part number for this extension cable is 1-900-800-86. | ||
| Sony | KV32XBR10 | HOR. OUTPUT FAILURE, SEE SB 161R1 | Dead Hor. Output Q-503 failed. | ||
| Sony | KV32XBR10 | NO OPERATION / REPLACE IC-101 (MICRO) | |||
| Sony | KV32XBR10 | HORIZONTAL LINES IN PICTURE, SEE N2207, AND N0413 | There were horizontal lines all through the picture. | ||
| Sony | KV32XBR10 | RETRACE LINE IN THE PICTURE, SHORTED Q-706 ON "C" BOARD | Green retrace lines in picture. | ||
| Sony | KV32XBR10 | BLANKED PICTURE, RESOLDER IC-500, IC-581, AND IC-582 | Have seen several ANU-1 sets with components mounted to theheatsink that have poor solder connections. | ||
| Sony | KV32XBR10 | CONVERGENCE OFF, REPLACED R-515, AND D-1514 | R-515 (22 Ohm 1/4W) A board was open, along with D-1514on the D Board was found shorted. Part number 8-719-300-65. -HQ COMMENTS: Diode D-1514 is the 28 volt rectifer schematiclocation F-15 on the D Board. This 28 volts is used in the VelocityModu | ||
| Sony | KV32XBR10 | PICTURE SLOWLY SHIFTS DOWNWARD, REPLACED IC-500 | Top of picture evidenced foldover. Entire image shifted slow-ly downward with time. | ||
| Sony | KV32XBR10 | INT. PIC SHRINKING, TROUBLE SHOOTING TIP FOR POWER SUPPLY | I have had several XBR sets with complaints of intermittentpicture shrinking. The solution was no regualtion of the B+ which waslowering under load. Here is a simple procedure that can be used whentrouble shooting this type of failure: Operate the set wi |