Dicas Reparação
Modelo - Chassis CCDF45
Pesquisa: CCDF45 Enviar Dica Resolvida
Resultados 21
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CCDF45 | NO POWER, PS503 | Immediately blows PS503 when power is applied. This was causedby FP90 shorting to ground as it bends near that point, allowing rubbingto occur and a short to develop. | ||
| Sony | CCDF45 | NO CAMERA VIDEO (GREEN) | No camera video, green screen. | ||
| Sony | CCDF45 | INTERMITTENT OPEN PS503 | The CCDF45 was intermittently blowing PS503, similar but notexactly the same as bulletin 164. | ||
| Sony | CCDF45 | SHUT DOWN IN REVIEW OR ANY REVERSE FUNCTION/Q-004/CC-26 BRD | Using scope, I traced signal from D301 supply reel sensor onFP 89 to IC001 on CC26 board to Q004 emitter. Q002 and 004 combinesignals into the matrix for takeup and supply reel sensing. I found Q004emitter to have a slightly more noise the Q002. | ||
| Sony | CCDF45 | WHITE STREAKS ON VTR PLAYBACK | White streaks on PB, appears to be an equalization problem. | ||
| Sony | CCDF45 | PART NUMBER FOR REC PROOF SWITCH TAPE SELECT | There is no part number listed for the REC proof switch onthis model. What is the part number? | ||
| Sony | CCDF45 | NO COLOR IN PLAYBACK | No color in Playback. EE mode is OK and tapes recorded inthis unit will Playback ok in other 8mm units. Also units had whitehorizontal streaks running through picture. Found Playback YC out atCN-502 pin 20 looked good but RF signal at base of Q-228 lo | ||
| Sony | CCDF45 | NO VIDEO | IC-202 had input but no output. Pin 14 0v, pin 12-15-18, 4.5vwhich is high. | ||
| Sony | CCDF45 | MECHANISM CHASSIS | Guide sticking when unloading process begins. Apparently,chassis is different - substitute part number is X-3749-038-1. -HQ COMMENTS: Please refer to Service Bulletin CSV-3 189 | ||
| Sony | CCDF45 | MECHANISM WILL NOT FUNCTION | Mechanism will not function. Pins 18, 17, 16 and 15 of IC-501minimum data was not changing. No output just 5VDC. | ||
| Sony | CCDF45 | EDGE DISTORTION/RAINBOWING OF AREAS OF HIGH DETAIL | Camera came in with no video - found bad imager. Replacedimager, and camera video had edge distortion and rainbowing. | ||
| Sony | CCDF45 | AUTOFOCUS SEARCH TO INFINITY | Autofocus searches to one direction and passes thefocusing point to infinity. | ||
| Sony | CCDF45 | REPLACEMENT LENS REQUIRES NEW SCREWS | The new lens has to be mounted with part number 3-335-640-11(2 each) screws. A service bulletin should be issued concerning themodels using this lens. -HQ COMMENTS: The CCD-F35/F36 and the CCD-F45/F46 use the new screws The part number of the CCDF35/36 | ||
| Sony | CCDF45 | DOES NOT RECORD | There was no 5V at pin 55 of IC-203 on CV-8 board. Thebase of Q-210 was 5.1V and would not go to 4.4V. | ||
| Sony | CCDF45 | INCORRECT PART NUMBER FOR D303 | Kansas City Parts substitutes the part number listed in theservice manual with 8-719-907-87, a diode. Since D-301 is shown on theschematic as the same as D-303, probably the correct part number should be8-719-820-44. |