Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | SPP110 | NO P/N FOR FLEX CONNECTOR PLUGS | Please advise p/n for plugs for flex connector (P/N1-624-678-11, Ref 904, page 41) plugs. A customer has a unit that iscorroded. See page 23 lower section, hand board, component side. -HQ COMMENTS: KCPS Checked with Tokyo regarding your inquiry.Unfort | ||
Sony | SPP110 | NO POWER | Handset had no power. | ||
Sony | SPP110 | PART NUMBER OF FUSE NOT LISTED IN SERVICE MANUAL | I couldn't get serial number but some SPP-110s have fuse(Ref No F-101) between L-604 and VDR601. Need supplement and part number. -HQ COMMENTS: You were looking at the SPP-110/150 service manual whichdoes not include the fuse. Please look at the SPP-1 | ||
Sony | SPP110 | 10.24 MHZ CRYSTAL REPLACEMENT DOES NOT FIT | When ordering and inserting a new 10.24 Mhz crystal, the newcrystal does not fit in the handset. -HQ COMMENTS: The reason for this is that there were originally 2 sizes:a short one for the handset and a tall one for the base. However, theyboth have the | ||
Sony | SPP110 | INTERMITTENT CHANNEL LOCK ON HANDSET | Intermittently the scanning of channels continues without itlocking on any channel. | ||
Sony | SPP110 | REPLACED BASE MOTHER BOARD AND ID TRANSMISSION DID NOT WORK | Order a brand new board to replace the one that customer haddrink spilled on. First board is broken near the AC adaptor andtelephone jack due to poor wrapping. Tried a second one, could not resetID code between base and handset. Reordered the third bo | ||
Sony | SPP110 | NO ACTIVATION DURING BATTERY SAVE | Unit works in normal mode but will not activate channelscanning in BATT SAVE mode. | ||
Sony | SPP110 | FRONT CABINET'S CLIPS OF THE HANDSET ARE BROKEN | Unit comes to the SSC with loosened cabinet at the batterycompartment due to the broken clips. The front cabinet can be repairedinstead of replacing it. | ||
Sony | SPP110 | PART NUMBER INCORRECT - IC208 | Above part number is incorrect. | ||
Sony | SPP110 | UNIT DOES NOT REDIAL CORRECTLY IN BATTERY SAVE MODE | Unit will only redial 8 digits reliably when going into Talkmode from Batt Save mode. Any additional digits are either not dialed atall or dialed incorrectly. However, when going into Talk mode from Norm(standby) mode, the redial function works flawles | ||
Sony | SPP110 | WHAT IS THE DISCONNECT TIME WHEN USING THE FLASH BUTTON | How long is the line disconnected for when using the flashbutton? -HQ COMMENTS: The line relay is opened for 500msec. | ||
Sony | SPP110 | ID TRANSFER BETWEEN BASE AND PORTABLE CANNOT BE COMPLETED | Will not assign security code when handset is placed on base. | ||
Sony | SPP110 | INCORRECT PART NUMBER | The service manual part list indicates IC-207 as part number,8-759-205-06 description TC74HC74F. This is incorrect, IC-207 is partnumber, 8-759-205-41 description TC74HC4066F substituted by part number,8-759-239-25 description TC74HC4066AF. Refer to se | ||
Sony | SPP110 | IMPEDANCE OF SONY TELEPHONE PRODUCTS | What is the impedance of our phone products? -HQ COMMENTS: All Sony phones fall in the range of 50 to 300 Ohms whenthe phone is off-hook and when DC-loop current is in the range of 15 -120 ma. | ||
Sony | SPP110 | NO CODE SENT TO HANDSET FROM BASE | Power light on Base continues to flash when Handset placed onBase. Handset is ok. Determined that code comes out of IC-501 pins 45 &46 then transmitted from Base to Handset over the air - not through topcharge terminals. When Handset placed on Base, c |