Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CCDVX3 | INTERMITTENT SNOW IN PIX/REPLACE FP522 | Unit had intermittent picture. Took shield off head amp(desoldered). Scoped CH 1 and 2 RF. Found no output CH 1. Touched inputat chip with dental pick and found CH 1 amp and Channel 2 working. Touchedinput with drum unplugged and found CH1 dead. | ||
Sony | CCDV99 | NO COLOR RECORDED/L603 (VI-55) OPEN | No color recorded on tape by this unit. Playback good of othertapes. | ||
Sony | CCDV701 | UNIT WILL NOT LOAD 20 MIN CASSETTES/CHECK DRUM BASE | During the loading process, 120 minute cassettes will load andplay normally (all other VTR functions work normally also). But when a 20minute cassette is inserted, the drum motor spins, take-up occurs, and theguides move in the load direction almost com | ||
Sony | CCDV101 | JAPANESE CHARACTERS FOR MONTH ON OSD, LCD DISPLAY OK | Due to water damage, we had to replace the SS99 board on thisunit. After installation, we could not get the OSD to display the datecorrectly. Either it was yy/mm/dd or mm/dd/yy, but with the month inJapanese characters. | ||
Sony | CCDTR91 | DIGITAL SOLARIZATION , IC604 | This camera had distortion that could be described as digitalsolarization. The picture was fine after heating A/D converter. | ||
Sony | CCDTR71 | NO ZOOM, STUCK IN MANUAL FOCUS ALL THE TIME NO MANUAL EXPOSU | Zoom did not work, auto focus did not work(stuck in manualfocus). No manual operation of exposure and program. | ||
Sony | CCDTR61 | LOUD BUZZ IN CAMERA AUDIO/REPLACE MIC UNIT | Loud buzz in camera mode. Audio playback of pre-recorded tapeis OK. But any tape recorded on this unit has a loud buzz recorded ontape. This buzz is also evident in E-E. Have subsituted good board forAU150 and MA170 with no change. Please help. | ||
Sony | CCDTR505 | BLOWS FUSE/CHECK SOLDERING ON IC903 | Intermittently will blow 1.6A main fuse. When it went badwould draw 1.5A in camera mode. | ||
Sony | CCDTR5 | REPLACEMENT PART WON'T MOUNT/SCREW TOO SHORT | Receive sub replacement A7040209K, and the assembly isthicker at the mounting where the fixing boss is attached(S/B cam 171).Making the original screw too short. USE A 1.4 X 3.0(7-627-551-57) SCREWINSTEAD OF THE 1.4 X 2.5 SCREW. -HQ COMMENTS: This has | ||
Sony | CCDTR5 | P/N FOR EVF LOWER CABINET NOT IN SERVICE MANUAL | The above part isn't in the service manual and I can't find aservice bulletin on this. | ||
Sony | CCDTR21 | NO AUDIO/CHECK L160 | No audio was caused by bad solder on one side of L160.Re-soldering corrected the problem. -HQ COMMENTS: L160 passes PB 5V. | ||
Sony | CCDTR200 | NO MECHNICAL MOTION/REPLACE IC201 | This unit came in in the unloaded position and would not load. IC903 was on and there was activity on pins 74, 75, 76 and 77. Theselines were also active at IC201 but, X201 was not oscillating. | ||
Sony | CCDTR101 | INT NO VIDEO IN PB OR INT B/W OF REC IMAGES, CHECK Q414. | Int. B/W and no video of Rec. material for this cam. Also,Int no video of PB pre-Rec material. Traced signal (Y comb out) to Q414,which had no signal on emitter (int) checked D.C. Voltages around Q414 anddetermined trans to be defective. | ||
Sony | CCDTR101 | CAMERA E TO E OUTPUT MOSAIC/DOWNLOAD GOOD EVR DATA | Both cameras were outputing a mosaic picture E to E. Core ICwas replaced and VC103 Board without solving the problem. | ||
Sony | CCDSP7 | CHANGE IN CABINET, R, EVF. | Service manual ID's ref #166 as #A7080563A. Supplement -1shows modified #166, and part changed from #X37251221 to #X37251223.KCP subs original part # with latest part #. Servicer says it doesn'tfit. Apparently ref #152, also modified in supplement -1 |