Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CDX5460 | LOSES POWER INTERMITTENTLY (REPLACED R536 P/N 1-216-073-00) | Power would cut out when input DC voltage would drop below14 volts. Found R536 to be a 50K ohm resistor instead of 10k. | ||
Sony | CDX5260 | SENSITIVE TO VIBRATIONS, FOUND DAMPER SHAFTS BROKEN, REF 117 | Unit skips very easily if it plays at all. | ||
Sony | CDX5060 | LOCK WILL NOT HOLD FACE PLATE (RE-POSITIONED SMALL SPRING) | Face plate will not lock onto unit. Appears lock is broken.Closer inspection revealed smaller spring misaligned. | ||
Sony | CDX5060 | NO FUNCTIONS/NO POWER (REPLACE IC503, P/N 8-759-167-50) | Unit had no functions or power. Found IC503 overheating dueto short. | ||
Sony | CDX4050 | SW807-SW816 PART NUMBERS NOT IN MANUAL (P/N IS 1-554-980-31) | Page 32 of service manual is missing switch part numbers. -HQ COMMENTS: The part number is 1-554-980-31, as shown in servicemanual supplement 1, which is currently being distributed to the field(10/11/94). | ||
Sony | CDX35RF | NOT CHANGING DISCS (REPLACED IC601, P/N 8-759-085-35) | Unit initialized ok and played disc one ok but when anotherdisc is selected display showed E99. Note: 1, mech moved up/down as ininitialize state, not trying to go to disc position. 2, EV sensor ok,when disconnected EV moved up. | ||
Sony | CDFX430 | NO POWER/RESOLDER CN504 | No power. -SOLUTION : Resolder CN504. | ||
Sony | CCDV5000 | UNIT SHUTS DOWN WHEN USING BATTERY/REPLACE IC103 | Unit ran fine on AC adaptor but would not ooperate withbattery. Tech was not able to perform battery down adjustment, no matterwhere set unit shut down at 6.3 volts. Battery sense line at themicroprocessor was changing when RV001 was adjusted at pin 4 | ||
Sony | CCDTR81 | TECHNICAL FLASH 89 PART IS INCORRECT | Tech Flash states that part A7048534A (E) was used. | ||
Sony | CCDTR71 | MODE SWITCH | Mode switch bad, mode switch is not available separately. Theone way to repair is to replace entire chassis , #301.Can you locate a part for mode switch separately. TR5 has part # but Idon't know if it is the same. -HQ COMMENTS: Because of the high pr | ||
Sony | CCDTR21 | INTERMITTENT 5 MIN WARNING/CHECK SOLDERING ON CN521, W522 | 5 min warning would intermittently show in v.f. even withfully rewound tape. Couldn't reproduce problem on bench. -HQ COMMENTS: Please check the soldering on CN521 and W522 on the SL-27board. | ||
Sony | CCDTR101 | NO EVF VIDEO AFTER WARM UP/REPLACE Q304 | After 10-15 minutes of camera or VTR mode EVF video goes out. | ||
Sony | CCDSC5 | SPRING DOES NOT COME WITH TG1 | diagram on pg 121 of CCDSC5 manual shows TG1 arm with thespring. The part does not come with the spring. | ||
Sony | CCDFX430 | LANC JIG PROBLEM | Servicer changed VS-110 MCB due to soldering problems withIC505 and IC503. Found board was locked in forced power mode. Theprocedure in the manual was confusing, but we found by setting powerswitch to VTR side while setting addresses 02 and 03 to data 00 | ||
Sony | CCDFX420 | PICTURE IN PLAYBACK CUTS IN AND OUT | Picture in playback will cut out/in. SOLUTION: Replace IC501. |