Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CDX5460 | CD DOES NOT PLAY, DISPLAY READS E-04 | The LCD display of the unit reads E-04. This may be caused bythe CD making contact with the chucking arm (ref# 122). This may cause theCD not to spin and eventually displaying an error message. | ||
Sony | CDX5460 | UNEXPLAINED ERROR CODE IN TEST MODE: "E-A0" | An unexplained error code appeared on the display while in thetest mode. The code is E-A0. -HQ COMMENTS: Tokyo told us that program bugs may account forunexplained error codes. In this particular case, the E-A0 appears whenthe unit tried to eject the | ||
Sony | CDX5460 | ERROR CODE E44 | Servicer has unit that customer complained it dropped out oncein awhile. Servicer has not been able to duplice problem. Put unit intest mode. After 6 hours of playing E44 came up on display but unit kepton playing. Noted FPR 03252. Here's another er | ||
Sony | CDX5460 | TEST MODE ERROR CODES EXPLAINED (SEE CAR BULLETIN # 373) | Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode. | ||
Sony | CDX5460 | E-04 CODE WHEN CD IS LOADED (REPLACED Q521 ON MAIN BOARD) | E-04 code on CD. Found Q521 regulator at 3.9v | ||
Sony | CDX5460 | NO CD FUNCTIONS (REPAIRED DAMAGED TRACE AND REPLACED D523) | No CD functions. Observed opened trace to base of Q520, andD523 was shorted. | ||
Sony | CDX5460 | EXTENSION CABLE FOR REPAIRING DISPLAY MCB (J-2502-009-7) | It may be difficult to repair the display MCB without using anextension cable. | ||
Sony | CDX5460 | LOSES POWER INTERMITTENTLY (REPLACED R536 P/N 1-216-073-00) | Power would cut out when input DC voltage would drop below14 volts. Found R536 to be a 50K ohm resistor instead of 10k. | ||
Sony | CDX5460 | WOULD NOT LOAD DISC, CAUSED BY SHORTED D523 | Unit would not load a disc. | ||
Sony | CDX5460 | WILL NOT ACCEPT CD, "LOAD" FLASHES (RE-ALIGN ST LEVER) | When disc is loaded, unit will not chuck disc and LOAD continues to flash. Disc is ejected a few seconds later. Found ST lever pinned between chassis (R) assy and slide lever in top chassis assy. | ||
Sony | CDX5460 | SCRATCHING NOISE WHEN CD STARTS OR STOPS | Units would make a scratching sound when the CD started up orwhen Off or Eject was pressed. | ||
Sony | CDX5460 | WILL NOT ACCEPT CD (RESOLDER Q2) | Q2 was cold soldered and was not detecting the CD beingloaded. | ||
Sony | CDX5460 | WILL NOT ACCEPT CD UNLESS FORCED IN (RESOLDER D802) | Unit will not accept CD until it is pushed in almost half way.Found D802 was not centered on PCB correctly and was not facing Q2 on MDboard. It appears this was done at the factory. | ||
Sony | CDX5460 | NO REMOTE FUNCTIONS (REPLACE IC802, P/N 8-759-515-60) | IC802 was receiving the proper voltages. IC802 Pin #2 wasnot sending out its carrier (pre) pulse. When a remote button was pressedthere was a pulse train. | ||
Sony | CDX5460 | WILL NOT ACCEPT CD (REPOSITION TENSION SPRING REF. # 129) | After re-setting, unit will usually take and eject first CDfine any CD's inserted after first one (or if first one is ejected andCD is pressed), the CD will only go half way and make a grinding noise.(Similar circumstances to my FPR# O3163). |