Dicas Reparação
Modelo - Chassis CDX5260
Pesquisa: CDX5260 Enviar Dica Resolvida
Resultados 29
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CDX5260 | CD DOES NOT PLAY, DISPLAY READS E-04 | The LCD display of the unit reads E-04. This may be caused bythe CD making contact with the chucking arm (ref# 122). This may cause theCD not to spin and eventually displaying an error message. | ||
| Sony | CDX5260 | UNEXPLAINED ERROR CODE IN TEST MODE: "E-A0" | An unexplained error code appeared on the display while in thetest mode. The code is E-A0. -HQ COMMENTS: Tokyo told us that program bugs may account forunexplained error codes. In this particular case, the E-A0 appears whenthe unit tried to eject the | ||
| Sony | CDX5260 | TEST MODE ERROR CODES EXPLAINED (SEE CAR BULLETIN # 373) | Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode. | ||
| Sony | CDX5260 | ERROR CODE E44 | Servicer has unit that customer complained it dropped out oncein awhile. Servicer has not been able to duplice problem. Put unit intest mode. After 6 hours of playing E44 came up on display but unit kepton playing. Noted FPR 03252. Here's another er | ||
| Sony | CDX5260 | NO POWER (REPLACED IC503, BA3910-V3, P/N 8-759-160-98) | No power, no display. | ||
| Sony | CDX5260 | EXTENSION CABLE FOR REPAIRING DISPLAY MCB (J-2502-009-7) | It may be difficult to repair the display MCB without using anextension cable. | ||
| Sony | CDX5260 | SENSITIVE TO VIBRATIONS, FOUND DAMPER SHAFTS BROKEN, REF 117 | Unit skips very easily if it plays at all. | ||
| Sony | CDX5260 | WON'T LOAD, MAKES CLICKING NOISE | Will not take CD's makes loud clicking noises. | ||
| Sony | CDX5260 | STARTS PLAY BUT DOESN'T CONTINUE (REPAIRED TRACES ON MD MCB) | CD goes into play, plays for 3-5 seconds. CD mech/FOP emitsfaint squealing noise as though sled circuit is starting to track. Uniteventually reads code E0-4. | ||
| Sony | CDX5260 | NO POWER, NO OPERATION (FOUND X502 DEFECTIVE) | Unit had no functions (no display or power up). | ||
| Sony | CDX5260 | E04 ON DISPLAY (CLEANED GREASE FROM S301 ON MOTOR BOARD) | E-04 on display after inserting CD. Found sled at outside ofdisc. Found S301 stuck (pushed in) so that micro thought sled was atcenter of disc. There seemed to be grease (black) on shaft of switch. | ||
| Sony | CDX5260 | PRE-AMPS POP DURING POWER ON/OFF. | When unit was turned on/off, there would be a loud distorted popping sound from the Pre-Amp outputs. The speaker outputs were fine. Found D101 and D201 were missing and appear to have never been installed at the factory. | ||
| Sony | CDX5260 | WILL NOT ACCEPT CD (REPLACE REF. # 124, P/N 3-384-888-01) | Unit would reset but would not accept CD. Found that locking tab on left slider had broken, allowing slide to slip off of shafts labeled B on main chassis assy. | ||
| Sony | CDX5260 | DOES NOT PLAY CD (REPLACE S301, P/N 1-572-467-31) | Sled is usually run all the way out. Service test mode displays E-14. Found the plunger on S301 stuck in. | ||
| Sony | CDX5260 | CD EJECTS AS SOON AS IT IS INSERTED (RE-SEAT SENSOR BOARD) | After the CD is inserted into the mech, it ejects it one second later. Found the sensor board popped out from the clip in the front. |