Dicas Reparação
Modelo - Chassis
Pesquisa: Enviar Dica Resolvida
Resultados 81534
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CCDF55 | WON'T THREAD A TAPE | Intermittently, drum won't start. | ||
| Sony | CCDF50 | NO CAMERA OR PLAYBACK VIDEO OUT | Unit had no camera, playback or EE video. Signal was goodgoing into input select IC-362 pin 28 (VA-Board). Video looked clipped atpin 11 and no signal was present at pin 4. Changing IC-362 had no effect.Found no serial data I/O at pins 20-23. Traced | ||
| Sony | CCDF40 | NO CAMERA OR PLAYBACK VIDEO OUT | Unit had no camera, playback or EE video. Signal was goodgoing into input select IC-362 pin 28. (VA-40 Board) Video looked clippedat pin 11, and no signal was present at pin 4. Changing IC-362 had noeffect. Found no serial data I/O at pins 20-23. Tr | ||
| Sony | CDP590 | NEED PINOUT FOR IC-401 | Can you supply us with a description of the pins on this IC?Which are inputs, which are outputs, etc? -HQ COMMENTS: Cannot locate pin out of this IC in any similar models.Will fax Tokyo for information. TO TOKYO: Could you please send block diagram and | ||
| Sony | KV27AVR | MISSING INFORMATION FROM SERVICE MANUAL | Vertical bias adjustment procedure: On service manual pageM-49: step 3 does not inform where the 16.5 +/- 0.1V test point is. -HQ COMMENTS: Please add the following information to your servicemanual: Step 3. Connect digital multimeter across DY connecto | ||
| Sony | KV27XBR15 | COLD SET HAS NO VIDEO FOR FIRST THREE MINUTES, REFER L1614 | When set is turned on cold, there is no video for the firstthree minutes. High voltage and all function check out ok except video ismuted coming out of IC-301 to CRT. Then the raster starts to blink on andoff for about 15 seconds and then the picture w | ||
| Sony | WMF200 | PROBLEM FIX - AUDIO OUTPUT LEVEL IS LOW | Found low audio output (Cassette). Found audio input existsat R-112/212 and amplification exists at R-113/213. | ||
| Sony | D66 | 1/2 VCC ADJUSTMENT POINTS | Manual does not give location of 1/2 Vcc point for adjustment. | ||
| Sony | CCDV99 | NO PICTURE ON PAUSE | When camera is in playback, put in pause, video will be lost(bad A head). Following the video path, found pin 20 HD-8 board hadone field missing when put in pause. Following it back, found that inpause, video switch between pin 5 and 3 IC-202 on the H | ||
| Sony | CCDTR5 | NO VIDEO OUT OF CAMERA | Connections on inner side of CN-301 on CD-14 board were bad.Voltage was on connector not on imager IC. | ||
| Sony | KV27XBR10 | PICTURE COMES ON SLOW AND FLASHES FOR FIVE MINUTES, | On first turn on, the picture or screen will come on veryslowly. When picture comes on, it will flash on and off until the set ison for five minutes. Unit will work well. This set has always done this. | ||
| Sony | SPP110 | FRONT CABINET'S CLIPS OF THE HANDSET ARE BROKEN | Unit comes to the SSC with loosened cabinet at the batterycompartment due to the broken clips. The front cabinet can be repairedinstead of replacing it. | ||
| Sony | WMF707 | AUTOMATIC SCAN NOT LOCKING | When changing frequency range of tuner from Japanese toAmerican, according to Customer Information, the tuner feature of lockingonto strong station signals is lost. When reverting back to Japanesefrequency range, the tuner will lock onto strong signals | ||
| Sony | CCDF45 | MECHANISM WILL NOT FUNCTION | Mechanism will not function. Pins 18, 17, 16 and 15 of IC-501minimum data was not changing. No output just 5VDC. | ||
| Sony | CDX7580 | PART NUMBER FOR FEED GUIDE MISSING | Part number for feed guide missing from manual. Part ispictured on page 40 of manual, connected to FOP (Ref. No. 926) by screws437 and 436. Kansas City researched this and the correct part number islisted above. -HQ COMMENTS: Thanks for researching th |