Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CCDF501 | NO PIX FROM VTR, NO PB RF (FOUND OPEN TRACE ON SS100 BOARD) | When camcorder is in play mode, no picture. No RF on pin 3of CN508 (PBRF testpoint). Also missing was switching 5V (REC/PB) on pins11/12 of CN501 and pin 25 of IC506. Also missing was 5V on pin 27 ofsame IC. Found power line 5V open between L502 and | ||
Sony | CCDF501 | INTERMITTENT LOCKUP, NO ERROR CODES/RESOLDER W505 | Servicer had two units exhibiting intermittent lockupproblems, sometimes causing tape to eject, sometimes causing functionbuttons to be inoperative. After initial indication of loading motorproblem, no error codes were recorded. By substitution, servicer | ||
Sony | CCDF50 | DRUM WON'T INITIALIZE PROPERLY, CAPS FAIL C0068 SS BOARD | Drum won't start up properly, hesitates, or won't start up atall. I found C0068 3.3mf @ 50v to be the main culprit, but ususally I goahead and change C069.71.74, 75 which are all 10mf @ 16v. These 5capacitors area ll tied to IC004 'drum drive and seem | ||
Sony | CCDF501 | WASHED-OUT PIX. IRIS CONTROL INOPERATIVE/REPLACE DC-DC | Iris control inoperative. Tried adjustment. After discoveringthat I had to release page D write protection by setting EF and FE on pageF to FF, I was still unable to get the iris to close. | ||
Sony | CCDF50 | APPEARS TO LOOK LIKE AGC TEARING C491/VA42 BD | When record from camera or line, the picture looks like ithas AGC tearing but playing pre recorded tapes picture looks ok. | ||
Sony | CCDF50 | EVF PIE-CRUST EFFECT, EE/PB MODE/REPLACE C915, VF-13 BOARD | Noticed a pie-crust effect on the VF on EE or PB mode. | ||
Sony | CCDF50 | NO VIDEO IN CAM MODE/LEAKY C633 ON VC62 CAUSED SHORT(V-SUB-G | No video from camera. Found V-sub line shorted to ground.Isolated to VC62 and found capacitor electrolite leakage caused carbonsubstance to form between V-sub trace and ground trace running parallel. | ||
Sony | CCDF50 | NO CAPSTAN MOTOR ROTATION/CHECK R058, Q051. | No capstan motor function, tape stuck, no function from VCRportion of camcorder, eject indicator flashing. Low voltage on pin 8 ofIC007 (PWM,VS) was caused by an open connection between R058 and base ofQ051. A wire bridge corrected the problem. -HQ COMM | ||
Sony | CCDF501 | VC-95 BOARD NEW FROM STOCK - NO AF/CHECK PAGE F ADD. EB | Servicer replaced VC-95 because of no video. (Board wasCracked.) With new board video was fine but focus motor will not run.Replaced board a second time with same problem. Checked and found no 4.9Vpin 38 of IC501. Original board was 1-639-034-12, new | ||
Sony | CCDF501 | NO MECH FUNCTIONS/REPLACE PS501 | Found PS501 open. | ||
Sony | CCDF501 | INTERMITTENT CAMERA OPERATION/REPLACE S514 | After the unit ran for a while in record, the power to camerawould become intermittent. The unit would go into standby and the tapewould cue and review all by itself. | ||
Sony | CCDF501 | NO VIDEO IN RECORD OR PLAYBACK | Video was muted in Record or Playback. -SOLTION: Mask pulse from digital titler IC-901 into IC-201. Pin 29would not end when video was input into IC-201 pin 3. This was becausethe sync det line into IC-901 pin 11 would not stay high. IC-501 (syscon)p | ||
Sony | CCDF501 | AF ADJUSTMENT COVER PART NUMBER | Could you please get me the part number for the small discwhich covers the auto-focus distance adjustment screw? -HQ COMMENTS: The part number for this is the same as for the CCD-F40 itis 3-725-181-01. There is stock available in KCP. | ||
Sony | CCDF501 | MIC WINDSCREEN PART NUMBER | Is the detachable mic windscreen available as a repair part?If so, what is the part number? -HQ COMMENTS: Please order part number X-2536-719-1. | ||
Sony | CCDF50 | NO PLAYBACK VIDEO AFTER WARM-UP | After five minutes, playback video goes dark and audio is ok.Changed IC-361 per FPR No. M0711 and it still malfunctioned. |