Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CCDV11 | WON'T LOAD/REPLACE C421 | Won't load, drum won't spin. | ||
Sony | CCDV101 | INT OR NO AUDIO/C562 LEAKS ONTO FEED OPENS CLOCK TO AU60 | Int or no audio, checked data lines into AU60 PCB. Found noSCK. Followed trace back and was open (int). Found leaky cap C562 overfeed through. | ||
Sony | CCDV101 | JAMMED MECH, NOISY AFTER REPAIR | The pin on the bottom of ref 353 is press-fit, and tends tocome loose. This causes it to disengage from the coaster spring, ref 356,and jam the mech. Putting a drop of super-glue on the pin and pressing itback in solves the problem. However, some of thes | ||
Sony | CCDV101 | TRANSPORT MOVES - NO EJECT/REPLACE CAPSTAN DRIVER IC | Unit would load & unload. Reels would not turn.Capstan would lock up in 1 position. Tried another motor by itself.Motor would start if it was spun up on eject. Motor would chatter thenstop. | ||
Sony | CCDV11 | NO CROMA E TO E OPEN TRACE UNDER C661 ON VC32A BOARD | No chroma from camera head. Checked C663, found chromasignal. Q620 base no signal. Trace between the two components, runsunder C661. Removed C661 and found leakage to corroded trace. | ||
Sony | CCDV101 | JAPANESE CHARACTERS FOR MONTH ON OSD, LCD DISPLAY OK | Due to water damage, we had to replace the SS99 board on thisunit. After installation, we could not get the OSD to display the datecorrectly. Either it was yy/mm/dd or mm/dd/yy, but with the month inJapanese characters. | ||
Sony | CCDV101 | NO (LEFT CHANNEL) AUDIO/REPLACE C425, AU-60 BOARD | No audio in left channel from Mic or in P.B. or in VTR in Rec.Replaced HIC401. Same problem. Checked DC voltages and compared L toR. Found Pin 7 on HIC (VG-A) O volts, but is supposed to be 2.5. FoundC425 shorted to ground, holding voltage down. | ||
Sony | CCDV101 | DEAD/REPLACE C-799 AND FUSE F-103 | Found blown fuse F103 caused by a shorted C799 on VA45 boardcoordinates F19 on page 154 of service manual. | ||
Sony | CCDV101 | NOT RECORDING RF FOR HEAD 2/REPLACE Q202, VS99 BOARD | Unit will not record RF for channel 2 head. Replaced HR10board. Problem still persists. Traced the signal on HR10 board - Foundno output at Pin 37/IC101 - DC voltage 0.06V higher then pin 24/IC101 -Found Q202 (SS99 board) leaky base collector. | ||
Sony | CCDV11 | CHROMA UNLOCK ON PLAYBACK | The chroma was unlocked on playback. This only occurred onself-recorded video, pre-recorded video was OK. | ||
Sony | CCDV11 | GUIDE ONE BASE ASSEMBLY REPLACEMENT PART DOES NOT FIT | Guide one base assembly does not fit properly. The inertialroller hit the side of the mechanism. | ||
Sony | CCDV101 | NO CASSETTE LOAD - EJECT WAS NORMAL | During Cassette Load, the drum would start but unit would notload and capstan would not turn. Using the cassette with the mode box, theunit would eject fine (load motor, capstan and drum would all run). Whentrying to load a tape while drum was running, t | ||
Sony | CCDV11 | CAUTION LIGHT ALWAYS ON - INTERMITTENT VIDEO FROM CAM | Caution light always is on and camera video is intermittent.The VTR functions are ok. Records ok from camera when video available. | ||
Sony | CCDV11 | SCREW FOR BASE (3) ASSEMBLY, GUIDE RAIL | Refer to CCD-TR5 FPRs No. M0215 and K1192. The numberA-7040-154-A chassis block assembly mechanical is now substituted with a-P. When installing the old (Ref. No. 309) base (3) assembly guiderail, one of the two (Ref. No. 319) screws will have to be re | ||
Sony | CCDV110 | "DC" MARK IN DISPLAY | Service bulletin No. CAM0199 instructs tech to replace abovepart if the DC mark appears in display. 180899021 now crosses to180899041 which still containes the DC mark. -HQ COMMENTS: Tokyo advises that 1-808-990-21 will be stocked again inWRPC and avai |