Dicas Reparação




Modelo - Chassis


Pesquisa: Enviar Dica Resolvida
Resultados 81393
Pedir dica reparação
MarcaModelo
(Chassis)
SintomaCausaSoluçãoPor:
SonyKV19TS20
TELEMATIC SETTINGS FOR P3B CHASSIS Could not find the Telematic settings for P3B chassis.
SonyCDPC90ES
MAGAZINE JAMS AND MOTOR M-602 RUNS CONTINUOUSLY The XA10B magazine jams when it is inserted into the unit andM-602 (Load/Save motor) runs continuously.
SonyWMFX55
BATTERY CONTACT TERMINAL NOT SUPPLIED We have received a few of these units with the battery doormissing. The battery door is available and in stock in Kansas City.However, the battery contact plate is shown as a separate part but is notsupplied. Can we get a part number generated for this
SonyCCDFX410
POWER TO EVF ONLY - NO OTHER FUNCTIONS EVF had power with CAM/VTR switch in any position. No otherfunctions would operate and EVF raster would not turn off. Suspected DCto DC control problem. Substituted DC to DC convergence PCB. No changein symptom.
SonyTAAV421
MISSING PART NUMBERS: IC953 AND IC956, 8-759-604-32/-39 We recently had an inquiry for p/n's for IC956 and IC953.After a great deal of searching, we finally found them in another s/m.The TA-AV421 s/m has many problems including missing pages, incorrectp/n's for reference no.s, p/n's missing, etc. Please chec
SonyCCDF56
PART NUMBER FOR FD-26 CABLE Servicer is trying to identify the part number for the FD-26cable (2 wires) that connectors the DC-DC converter to the W-991 connectoron the FU-72 board. -HQ COMMENTS: These types of cables are not being suppied by Tokyo. Wewill try and obtain a special
SonyCCDF340E
NO CAMERA VIDEO Unit would playback prerecorded tape fine but had no E-E videooutput. A technician had replaced the VC-39 board but this did notcorrect the problem. Because this unit is PAL the service manual wasloaned to the service center from the technical departme
SonyHST211
SCHEMATIC ERROR: Q512 HIGH SPEED SWITCH The schematic diagram indicates (page 11 of s/m) that the B+and B- supplies will be shorted if Q512 is activated to switch to the highspeed dub mode. This is obviously incorrect. Please notify Tokyo of theproblem so that a correction can be made to the
SonySLV585HF
CRICKET TYPE NOISE WHEN PLAYING NORMAL AUDIO TRACK After the unit warms up, mostly in EP mode, a cricket-likesound is heard in the background only when playing normal audio track.
SonyHCDH1600
NO AM OR FM AND DISPLAY WAS OK IC-21 on TCB-011, no oscillator on pins 1 and 24 and no B+ onpin 20 (approximately 1V).
SonyKV32XBR51
NO AUDIO OR VIDEO, REPLACED DIODE D-112 Diode on serial clock line would not pass the clock pulses.This was a troubleshooting problem. In ANU chassis if the data or CLK isbad, there is no vertical drive output from IC-301. This unit had Vdrive, therefore, data and clock to IC-301. However,
SonyDTC59ES
PRIOR MODELS PROVIDED ACCESS TO INFO ON DRUM USAGE TIME Prior generation models provided access to information on drumusage time and cassette cycles. This service mode also allowed you toenter Play mode with no cassette in place. There is no mention of thisservice mode in the service manual for this model a
SonyKV27HSR10
NO AFC - HORIZONTAL UNLOCKED, REPLACED C-322 Horizontal was unlocked went into service mode and tried autohorizontal frequency adjustment and set went into HV shutdown. Triedmanual Hor freq. adjustment and got a good adjustment however the hexdata was 01. I've never seen the data this low for thi
SonyTCC5
IC-833 AND BOARD MISSING Unit would go into Play Pause. A second unit worked ok andhad an additional MCB with IC-833 on it. When this MCB was installed inthe two defective units, each worked normally. This IC or MCB is notshown in the service manual. -HQ COMMENTS: We will co
SonyCCDFX410
SHUTS DOWN Intermittent shuts down in Play mode or Eject modes. Showstrianble in EVF. Have had two others with the same problem.


Assistência TécnicaAs dicas apresentadas destinam-se a técnicos de eletrónica, a tentativa de reparação ou assistência sem ter conhecimentos de eletricidade e eletrónica, podem provocar danos mais graves aos equipamentos e, devido a tensões muito elevadas em alguns circuitos, graves danos fisicos que podem constituir um risco em determinadas reparações.

Não arrisque reparar equipamentos com tensões elevadas se não tiver conhecimentos técnicos para o fazer em segurança.

Verifique se o esquema está disponível na área de downloads