Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CCDF55 | XSISTOR SUB IS TOO BIG; 8-729-905-36 WILL WORK | Ordered above surface mount xsistor from NPC and received872912028 2SC1623. This part is physically 2.7mm wide vs 2.0mm for theoriginal part. I don't think it will work since lands are extremely closetogether. This is a very common xsistor in all cam | ||
Sony | XVT33 | WEAK COLOR: RESOLDER C327 EN-5 BOARD | Tinted white/weak color. | ||
Sony | STRAV1070X | LAST CHARACTER IN CUSTOM FILE DISPLAY SCRAMBLED - IC202 | Last letter of custom file display scrambled. | ||
Sony | SL2000 | NP-1B BATTERY WON'T CHARGE IN AC220: SEE FPR K0682 | Parts deptartment is subbing NP1B Battery from B & P groupfor original NP1 for this portable Beta VCR. However, the dealer iscomplaining that customers' AC adapter won't recharge NP1B at all. Willsomething else work or can we change something in AC220 | ||
Sony | BM560 | REC SPRING NO LONGER AVAILABLE, P/N RESTORED | The tech bulletin describes a procedure for replacing brokenrec. springs. This part number is no longer available. It was initiallyused in the BM510/550 and the BM560 as this model is mechanicallyidentical. Dealers will require this part for some time | ||
Sony | CFSW430 | BATTERIES BURST AND LEAKED | Customer used wrong power cord when operating from AC.Battery disconnect switch was not activated by a smaller plug. As aresult, the unit power supply was providing continuous charge voltage onbatteries. -HQ COMMENTS: The part number of the power cord | ||
Sony | SPPA60 | NO POWER IN BASE - RESOLDER D5 | No power in base. Measured voltage on D5 and found it to becold soldered. This also pertains to serial numbers 35421 and 69370. | ||
Sony | D303 | NO MECHANICAL MOTION OF SLED MOTOR - TIGHTEN M-902 | The unit turns on but there is no mechanical motion becausethe wire connected to the feed motor assembly M902 is cut off. The feedmotor is not mounted securely. The screw to mount the chassis wasloosened either by shock or the vibrations of the motor r | ||
Sony | FD555 | INTERMITTENT PICTURE, AND BRIGHTNESS. RESOLDERED C803 | The unit would intermittently loose picture or brightnesslevel, when touching the board it would change. The horizontal osc.signal level changed between the positive and negative side of C-803horizontal drive couplying capacitor which delivers the horiz | ||
Sony | CCDTR200 | RATTLE NOISE/NORMAL OPERATION WHEN NO POWER IS APPLIED | The customer complained of a rattling noise when the camera isshaken back and forth. | ||
Sony | KV27EXR20 | "H" BRACKET PART NUMBER MISSING, 4-397-916-02 | On the chassis exploded View I need the plastic bracketbehind reference number 3, which clips on to the H Board. This partnumber was omitted from the Service Manual. -HQ COMMENTS: The part number is 4-397-916-02. This part is notavailable from KCP at | ||
Sony | KV27EXR25 | "H" BRACKET PART NUMBER MISSING, 4-397-916-02 | On the chassis exploded View I need the plastic bracketbehind reference number 3, which clips onto the H Board. This partnumber was omitted from the Service Manual. -HQ COMMENTS: The part number is 4-397-916-02. This part is notavailable in KC at this | ||
Sony | KV32XBR95S | NO CHANNEL CAPTION IN AUX MODE, NORMAL | In the aux mode the customer can not use the Channel Captionfeature (example channel 4 as NBC). When they bring up the menu thescreen turns gray. There is no mention of this in the Owners Manual. -HQ COMMENTS: This is normal operation, the Channel Cap | ||
Sony | KV27XBR95S | NO CHANNEL CAPTION IN AUX MODE, NORMAL | In the aux mode the customer can not use the Channel Captionfeature (example channel 4 as NBC). When they bring up the menu thescreen turns gray. There is no mention of this in the Owners Manual. -HQ COMMENTS: This is normal operation, the Channel Cap | ||
Sony | CCDFX310 | NO CAMERA PICTURE E-E/REPLACE IC 704 | There was no camera picture E-E and there was intermittentcharacter display. When character display rolled vertically, I foundthere was no VD out at pin 73, IC704. |