Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | KV32XBR95S | LOW AUDIO LEVEL FROM TV AUDIO OUTPUTS TO SAVA3 | When using the variable audio ouputs to drive the SA-VA3,the speakers would return to standby unless the volume level was increasedbeyond the customers preference. Not enough signal for vox controlcircuit in the SA-VA3 to work with. There was no probl | ||
Sony | KV32XBR95S | LOW AUDIO LEVEL FROM VARIABLE AUDIO OUTPUTS WITH EXTERNAL SP | When using the variable audio ouputs to drive the SA-VA3(External Audio Speaker system), the speakers would return to standbyunless the volume level was increased beyond the customers preference.Not enough signal for vox control circuit in the SA-VA3 to | ||
Sony | KV32XBR95S | PIX REPEATED ON LEFT SIDE,TOP 1/3 PIX DARK, REPLACED M BOARD | Picture repeated on left side of screen. Top 1/3 of picturewas dark. SOLUTION: Replaced M Board. | ||
Sony | KV32XBR95S | VOLUME FLUCTUATES IN SURROUND MODE, REPLACED X3 BOARD | Volume fluctuates in surround mode. | ||
Sony | KV32XBR95S | BLACK LINES IN PICTURE AFTER WARM UP, REPLACE C1511 ON A PCB | Picture distorted on top screen. Black lines horizontally,lines will come on after set warms up. | ||
Sony | KV32XBR95S | INTERMITTENTLY SIDES OF PIX PULL IN, RESOLDERED Q605 ON G BD | Sides pulled in, 60 cycles going thru pix , very intermittent. | ||
Sony | KV32XBR95S | FLUCTUATION OF AUDIO VOLUME ON STEREO BROADCAST, X3 BOARD | Unit displayed problem with audio volume fluctuating up anddown on stereo broadcast. | ||
Sony | KV32XBR95S | FUSE INSIDE SPEAKER BOX PART NUMBER, 1-518-645-11 | Part number for the fuse (lamp) inside the speaker box ismissing from the service manual. -HQ COMMENTS: The part number is 1-518-645-11. | ||
Sony | KV32XBR95S | NO AUDIO EXCEPT FIXED MONITOR OUTPUT, REPLACED X3 BOARD | No audio execpt from fixed monitor output. | ||
Sony | KV32XBR95S | SCHEMATIC DIAGRAM OF CRT PIN ALLOCATIONS ARE INCORRECT | The schematic diagram of the CRT pin allocations, on page114, are incorrectly labeled. The C Board lay out is correct. -HQ COMMENTS: Please refer to the schematic diagram located in theService Manual of the KV-27XBR96S for the correct pin allocationsch | ||
Sony | KV32XBR95S | SPEAKER RATTLE, REPLACED TWEETER | Speaker cone rattles with nominal volume. | ||
Sony | KV32XBR95S | MAIN PICTURE SHOWING THROUGH PIP, COLD SOLDER ON Q3001/3005 | The main picture shows through the PIP. You can see movementbehind the PIP picture. | ||
Sony | KV32XBR95S | VERTICAL DISTORTION, REPLACED IC1501 (VERT OUTPUT IC) | Transparent horizontal line through the middle of thepicture, with small amount of fold over at the top of the screen. Theproblem occurred after 10 minutes. Applying freeze spray to the verticalOutput IC1501, would cause the problem to disappear. | ||
Sony | KV32XBR95S | NO STEREO ON STATIONS,REPLACED Y2 BOARD,REAR SPEAKERS OFF | This is a followup to FPRO0339. Because of substandard cablesignal, some local channels stereo are not decoded by the cust unit. OtherSony TVs and VCRs on same system work OK. We tried adjusting set per S/Mbut it did not help. I sent Y2 board to servi | ||
Sony | KV32XBR95S | PICTURE WAS TOO WIDE, REPLACED D509, Q502, Q513, AND Q506 | The width was way out and I was unable to adjust it. I foundthe -5v line measuring -2.5v so I checked and replaced the D509 Zenorregulator, Q502 and Q513 pin drive transistors. -5v returned to normalhowever the picture was still too wide. I found Q506 |