Dicas Reparação




Modelo - Chassis


Pesquisa: Enviar Dica Resolvida
Resultados 81402
Pedir dica reparação
MarcaModelo
(Chassis)
SintomaCausaSoluçãoPor:
SonyCDX5060
NO FUNCTIONS, JUMPER RESISTOR JR801 MISSING FROM DISPLAY MCB Only the clock operated properly, all other functionsinoperable. The problem was caused by a missing jumper/JR801. JR801 isnot identified in the service manual.
SonySPP190
WEAK RECEPTION IN HANDSET - R6/R7 SWAPPED ON HANDSET PCB H/S had weak reception. After measuring Q1, Q2, Q3, I foundthat Q3 had 6V on the collector. The transistor measured good out of thecircuit. I checked all the caps in the area and they all turned out OK.While checking the resistors, I saw that R6 and
SonyCCDTR101
CAMERA VIDEO HAD SOLARIZED EFFECT/REPLACE IC708 Camera looked like soloarzation(see tape).
SonyCCDFX310
PARTIAL ZOOM OPERATION/REPLACE C872 CS-37 BOARD When zooming to wide angle, the zoom drive would stop, and thezoom display was incorrect. IC852 pin 3, 9, and 10 had input from zoompotentiometer. Pin 10 of IC852 was .97 volts instead of 2.7 Volts.
SonyCCDFX510
WRONG P/N FOR FP-558/CORRECT NUMBER IS 1-643-555-11 Item 107 on page 153 of service manual has the wrong partnumber, when ordering 1-645-271-11, the flex connector is only about oneinch long. The original flex connector is about 4 1/2 inches long. Inaddition, on page 87 it's described as FP558.
SonyD303
THE UNIT WILL TURN ON BUT NO FUNCTION - IC504 DEFECTIVE The unit is powered on but no function at all. The displaylight blinks. The voltage at pin 4 and pin 30 IC504 should be 4.5VDC.However, it varies from 1.5VDC to 4.5VDC at pin 4 and pin 30/IC504.
SonyKP61V15
SHUTDOWN, REPLACED C1718 ("D" BOARD) TV is very hard to trouble shoot due to very poor design.Request follow-up for a better way to work on TV.
SonyKV27TS36
BUZZING, VDR603 (D BOARD) TOUCHING SHIELD When set is turned on, a buzzing sound occurs. Home techin Burbank found VDR603 touching the shield.
SonyGEN-TVP
GENERAL INSTRUMENTS CABLE BOX NEEDS CODE IN OM, #65 Home tech informed me that the operators manual for severalTV models do not list the code for General Instruments. (example:KV27T529)(RMY118). He found the code to be 65, which is the same asJerrold.
SonyKV27XBR95S
SERVICE MODE DATA WON'T CHANGE, REPLACED IC205 In service mode, certain adjustments would not change data onscreen. Found stand-by 5V to be noisy.
SonyCDU31A-LL
IC 215 PART NUMBER/THE NUMBER IS: 8-759-175-80 WHAT IS THE PART # FOR THIS IC? IT IS NOT LISTED IN SM. -HQ COMMENTS: The Part Number is: 8-759-175-80. IC-215 is the ROM Chipfor this unit and contains the firmware version 1.2a. A Service Bulletinwill be issued.
SonyCDU31A-81
IC 215 PART NUMBER/THE NUMBER IS: 8-759-175-80 WHAT IS THE PART # FOR THIS IC? IT IS NOT LISTED IN SM. -HQ COMMENTS: The Part Number is: 8-759-175-80. IC-215 is the ROM Chipfor this unit and contains the firmware version 1.2a. A Service Bulletinwill be issued.Please Note that the SSC Should not be
SonyCDU31A-DC
IC 215 PART NUMBER/THE NUMBER IS: 8-759-175-80 WHAT IS THE PART # FOR THIS IC? IT IS NOT LISTED IN SM. -HQ COMMENTS: The Part Number is: 8-759-175-80. IC-215 is the ROM Chipfor this unit and contains the firmware version 1.2a. A Service Bulletinwill be issued.Please Note that the SSC Should not be
SonyCDU31A-01
IC 215 PART NUMBER/THE NUMBER IS: 8-759-175-80 WHAT IS THE PART # FOR THIS IC? IT IS NOT LISTED IN SM. -HQ COMMENTS: The Part Number is: 8-759-175-80. IC-215 is the ROM Chipfor this unit and contains the firmware version 1.2a. A Service Bulletinwill be issued.Please Note that the SSC Should not be
SonyCDXU500
PART NUMBER ADDITION: SPRING SHAFT (P/N 3-368-788-02) The service manual does not show a part number for the springshafts. These are the shafts which are shown to the right of ref. 3 onthe left side of the mechanism, and to the left of ref. 3 on the rightside of the mechanism. -HQ COMMENTS: The part numbe


Assistência TécnicaAs dicas apresentadas destinam-se a técnicos de eletrónica, a tentativa de reparação ou assistência sem ter conhecimentos de eletricidade e eletrónica, podem provocar danos mais graves aos equipamentos e, devido a tensões muito elevadas em alguns circuitos, graves danos fisicos que podem constituir um risco em determinadas reparações.

Não arrisque reparar equipamentos com tensões elevadas se não tiver conhecimentos técnicos para o fazer em segurança.

Verifique se o esquema está disponível na área de downloads