Dicas Reparação
Modelo - Chassis 1000
Pesquisa: 1000 Enviar Dica Resolvida
Resultados 340
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | SCD1000 | INVALID LORAN - POSITION COORDINATES STUCK | No valid loran. Receiver will never provide position solution(valid). Loran coordinates are stuck (no change). It seems that softwareversion has no relation to this problem (182C, 182E and 182F). | ||
| Sony | TAE1000ESD | UNIT WOULD NOT POWER UP | Unit would not power up. Found C-916 floating around looseinside of unit. Capacitor looked to be cut away from the Main board.Put a new capacitor in unit and the unit came up and ran. This is thesecond unit I have seen with this problem. -HQ COMMENTS: C | ||
| Sony | TAE1000ESD | INTERMITTENT POPPING NOISE IN REAR SPEAKERS | Intermittent popping noise in rear speakers. | ||
| Sony | TAE1000ESD | PART NUMBER FOR DISPLAY PCB WITH ALL COMPONENTS | We are trying to order a mounted display board with allcomponents. The service manual only lists a bare PCB. Is it possible toget a complete board? -HQ COMMENTS: According to KCPs information, you can't get a complete PCboard if the PC board has less | ||
| Sony | STRAV1000 | SPEAKER PROTECTION ALWAYS ON | The speaker protect circuit is always engaged. The problemappears to be related to the power supply. We noted that the schematicshows two separate grounds. In fact there is about 3 volts differencebetween the two. When the two grounds are tied togeth | ||
| Sony | SLHF1000 | NO BETA HI-FI RECORD | No Beta Hi-Fi Record. Playback or pre-recorded material ok.All voltages ok on IC-004. Missing switching voltages at pin 44 IC-003.Found open foil between Q-610 and D-606. Simulated shorted transistor. | ||
| Sony | SLHF1000 | POOR PICTURE BETA I | Poor Record/Playback of Beta I - marginal tracking. Picturequality is grainy. RF envelope lower than normal - most noticeable inBeta I. Found voltage at IC-004 (PV-2) board to be 4.9V at pins 1 and 2.Discovered R-16 to be 10 Ohms instead of 1 Ohm. Pr | ||
| Sony | TAE1000ESD | HUM WHEN USING SUBWOOFER AND CENTER CHANNEL OUTPUTS | 60 Hz hum heard at subwoofer speaker, when subwoofer amplifieris turned on to max volume out. | ||
| Sony | TAE1000ESD | NO P/N LISTED FOR THE CAPS THAT COVER THE OPTICAL INPUTS | The small plastic covers that are inserted into the opticalinputs when they are not being used do not have a part number. They arenot shown on the exploded view, nor are they listed in the parts list.We have a customer that did not receive them with his | ||
| Sony | TAE1000ESD | REMOTE COMPATIBILITY PROBLEM WITH STR-AV560 REMOTE | The customer has a TAE-1000 and a STR-AV560. He uses theSTR-AV560 for a tuner and a rear channel amplifier. When he selects tunerpresets with the STR-AV560 remote, the surround mode on the TAE-1000changes. Similarly, when changing surround modes with | ||
| Sony | DTC1000ES | EATS TAPES | FF arm assembly very stiff movement causing slow return ofpinchroller to cassette when ejecting. The pinchroller is also veryglazed. | ||
| Sony | M1000 | DIFFERENT SERVO BOARD | The above unit has a servo board that is different from theone in the schematic. The board contains an IC instead of the discretetransistor. Can you supply any information about this? -HQ COMMENTS: The servo PCB and the Motor are available under one p | ||
| Sony | SLHF1000 | TRACKING PROBLEM, INPUT OF ONE HEAD IS LOW | In playback, unit has noisy video, tracking shift causes noiseto worsen. Symptom appears to be a bad head. RF output shows little orno output from one head, the other is o.k. Tracking shift causes thelevel to increase on one head and decrease on the o | ||
| Sony | VTX1000R | NOISE IN PICTURE | Interference in picture caused by frequency beating the video.The higher the channel number, the more intense the noise. | ||
| Sony | TAE1000ESD | CANNOT MONITOR WHILE EFFECT RECORDING ON TA-E1000ESD | If effect recording using Tape 2 output and monitoring thesource, an oscillation is heard. This only happens when effect recordingrecording non-processed signal works fine. -HQ COMMENTS: This is normal operation for this unit. It is designedthe same a |