Dicas Reparação
Modelo - Chassis SPP11
Pesquisa: SPP11 Enviar Dica Resolvida
Resultados 44
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | SPP115 | PART # IN MANUAL IS FOR PC MOUNT NOT SURFACE MOUNT. | Ic is through board mount (should be surface mount). | ||
| Sony | SPP110 | NO P/N FOR FLEX CONNECTOR PLUGS | Please advise p/n for plugs for flex connector (P/N1-624-678-11, Ref 904, page 41) plugs. A customer has a unit that iscorroded. See page 23 lower section, hand board, component side. -HQ COMMENTS: KCPS Checked with Tokyo regarding your inquiry.Unfort | ||
| Sony | SPP115 | MUTED AUDIO (IN AND OUT) IN HANDSET - X-502 BAD IN BASE. | Unit's handset locks up with the base but audio was muted(both receive and transmit). Tested handset on the BK analyzer and Iverified it was good. Going to the base, traced audio back to the telline duplexer IC. I measured the pins around the IC and a | ||
| Sony | SPP115 | NOT CHARGING - REPOSITION BATTERY CONTACTS | Base would not charge batteries. | ||
| Sony | SPP110 | NO POWER | Handset had no power. | ||
| Sony | SPP115 | TEST MODE PROCEDURES FOR BASE UNIT | The procedures for putting the base unit in test mode areunclear in the service manual. -HQ COMMENTS: The correct procedures for putting the base unit in testmode are as follows:1. Disconnect battery pack. 2. Unplug AC Adaptor. 3. Connect IC-501/pin 11t | ||
| Sony | SPP115 | HANDSET CUTS OFF | Handset suddenly goes dead because of ID TX design. When talkis pushed, handset cannot retrieve channel to line. This usually happenswhen handset is tapped, shaken or flexed. | ||
| Sony | SPP115 | NO RING OR KEYPAD BEEP | The handset doesn't ring and the keypad doesn't beep. | ||
| Sony | SPP115 | ID ROM DEFECTIVE | New ID ROM received from NPC is defective. This is the secondtime this has happened. | ||
| Sony | SPP115 | NO DIAL TONE | No dial tone. | ||
| Sony | SPP110 | PART NUMBER OF FUSE NOT LISTED IN SERVICE MANUAL | I couldn't get serial number but some SPP-110s have fuse(Ref No F-101) between L-604 and VDR601. Need supplement and part number. -HQ COMMENTS: You were looking at the SPP-110/150 service manual whichdoes not include the fuse. Please look at the SPP-1 | ||
| Sony | SPP110 | 10.24 MHZ CRYSTAL REPLACEMENT DOES NOT FIT | When ordering and inserting a new 10.24 Mhz crystal, the newcrystal does not fit in the handset. -HQ COMMENTS: The reason for this is that there were originally 2 sizes:a short one for the handset and a tall one for the base. However, theyboth have the | ||
| Sony | SPP115 | UNIT DOES NOT WORK AFTER MAIN BOARD IS REPLACED | The unit does not work after the main board in either the baseor the handset is replaced. -HQ COMMENTS: The replacement boards have blank ID ROMS. Therefore,after replacing either the handset or base unit board, remove the ID ROMsfrom both old boards ( | ||
| Sony | SPP110 | INTERMITTENT CHANNEL LOCK ON HANDSET | Intermittently the scanning of channels continues without itlocking on any channel. | ||
| Sony | SPP115 | CANNOT PUT HANDSET IN TEST MODE | The procedure in the service manual on putting the handset inthe test mode does not work. -HQ COMMENTS: Tokyo fax (T91032). The correct procedure for putting thehandset in test mode is as follows. 1. Put unit in RINGER ON mode.2. Press Talk while holdi |