Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | LANCJIG | EVR TRANSFER WRITES ZEROS INTO VSUB ADJUSTMENT ADDRESSES | When transfering data to a CCD-TR61, the LANC Jig wrote zerosinto page F addresses 4 and 5. These are the Vsub and VRG addresses. -HQ COMMENTS: It is only possible for this to happen one way and that isby using version two data files with version one so | ||
Sony | LANCJIG | CCD-TR61 AND CCD-TR91 LOCK UP EVR TRANSFER AT PAGE F ADDR 0 | The CCD-TR61 and CCD-TR91 lock up at page F address 0. Can youplease check into this? -HQ COMMENTS: Both cameras work when tranfering data from the samemodel. This problem only occurs when trying to transfer data from onemodel to another, for example t | ||
Sony | LANCJIG | COMMUNICATIONS ERROR OCCURS IMMEDIATELY IN EVR TRANSFER/ADJ | A communications error occurs immediatley upon initiating theEVR transfer. As soon as the page to transfer(to or from the camcorder)is selected from the main menu, the error occurs. -HQ COMMENTS: This error occurs most often when the adjustment modesimu | ||
Sony | LANCJIG | TRANSFER FROM CAMERA TO COMPUTER LOCKS UP AT 3F | Using CCD-FX511, upload locks up at address 3F. Please provide assistance. -HQ COMMENTS: This address is critical for timing. Any problem at thisaddress indicates a problem with either the autotiming of the program orthe adjustment of the ad | ||
Sony | LANCJIG | DOES NOT AUTOTIME WITH A 486 55MHZ OR 66 MHZ COMPUTER/TECHRP | The auotiming does not function properly with a 486 55mhz or66 Mhz computer. -HQ COMMENTS: This problem has not been verified at this time. In theevent that this should happen, have your technical representative contactheadquarters for a possible solut | ||
Sony | LANCJIG | PORT 4 DOES NOT OPERATE; JUMPER IC5 PIN6 TO NEAR SIDE OF R7 | Port 4 of the jig does not operate, all other ports are OK | ||
Sony | LANCJIG | CCD-F301 DOWNLOAD, LANC SOFTWARE 1-2.0 | |||
Sony | LANCJIG | EVR TRANSFER DOES NOT WORK WITH CCDTR51/NEW SOFTWARE | EVR transfer gives a communication error on the CCD-TR51. Thejig stops on page D address 3E and page F address AF. -HQ COMMENTS: This was due to a model setup error in the software. Ithas been corrected and new software is on the BBS. | ||
Sony | LANCJIG | LANC JIG WORKS WITH EVC-40/50 | If control L switch is set to S position, this unit may be runon Lanc Jig to check for intermittents or to just verify operations. -HQ COMMENTS: This is correct, any VCR with a control L input shouldfunction correctly. As you stated they must be in sla | ||
Sony | LANCJIG | NO CUE OR REV OPERATION WITH OLDER MODELS | Isreal reported that there is no cue or review operation witholder models CCD-F70 and CCD-F45 were examples. -HQ COMMENTS: We will check into this as some of the LANC codes havebeen slightly changes over the years. | ||
Sony | LANCJIG | JIG DOES NOT FUNCTION AFTER INSTALLING NEW SOFTWARE;AUTOTIME | After installing the new software version, the jig will notfunction. | ||
Sony | LANCJIG | EVR TRANSFER DOES NOT WORK FOR ONE PAGE CAMERAS; NEW SOFTWAR | One page cameras do not work for EVR transfer. | ||
Sony | LANCJIG | NO COMMUNICATION WITH COM 3 SELECTED; SELECT IRQ 10 | I have no communication when I select com 3 in the systemparameters menu. |