Dicas Reparação




Modelo - Chassis KV27XBR65


Pesquisa: KV27XBR65 Enviar Dica Resolvida
Resultados 16
Pedir dica reparação
MarcaModelo
(Chassis)
SintomaCausaSoluçãoPor:
SonyKV27XBR65
HOR. OUTPUT FAILURE, SEE SB 161R1 Dead Hor. Output Q-503 failed.
SonyKV27XBR65
INTERMITTENT SHUT DOWN, REPLACED Q506 Intermittent shut down.
SonyKV27XBR65
BARKHAUSEN OSCILLATION, RESOLDERED FBT CONNECTIONS We received some reports of barkhausen oscillation which maybe intermittent in nature and sometimes signal strength dependent. Theproblem is caused by a poor ground connection on the focus block sectionof the flyback.
SonyKV27XBR65
NO COLOR FOR FIRST FEW MINUTES, REPLACED X-301 Parent picture had no color for first few minutes and thenwould normalize. Child picture normal with color. Osciloscope showedgood chroma signal at IC-301/pin 5 (Chroma-In). When scoping 3.58 os-cillator (X-301), found it to be intermittent.
SonyKV27XBR65
INT. PIC SHRINKING, TROUBLE SHOOTING TIP FOR POWER SUPPLY I have had several XBR sets with complaints of intermittentpicture shrinking. The solution was no regualtion of the B+ which waslowering under load. Here is a simple procedure that can be used whentrouble shooting this type of failure: Operate the set wi
SonyKV27XBR65
ANODE CONNECTOR MISSING ON NEW "A" BOARDS, SEE SB 108 When replacing the A board, the anode wire from the flybackis missing. Is there a part number for it? -HQ COMMENTS: Please order part number 1-540-006-32, which is the AnodeCable. This was covered in Service Bulletin number 108. Future A Boardswill co
SonyKV27XBR65
IC-101 DOES NOT MATCH P/N IN MANUAL, 8-759-633-67, SB 092 Above part number does not match with the part called for inthe service manual. -HQ COMMENTS: During production, the microprocessor was changed. Thesetwo ICs are not interchangeable. Please check to see what micro is beingused before ordering from KCP
SonyKV27XBR65
LOUD HIGH PITCHED SOUND FROM SET, APPLIED SILICONE (T-602) Loud, high pitched noise from set, not emitting from the audiocircuit. Sounds similar to yoke with a squeling problem. Before replaingyoke please read.
SonyKV27XBR65
HORIZONTAL RGB LINES IN TOP PORTION OF PIX, SEE SB # 76 Unit looks normal but, displays red, green and blue horizontallines on the top portion of the picture. Normally, adjusting the REFfunction in the service mode will shift the lines out of the picture area.However, in this case the shift was not enough.
SonyKV27XBR65
NO PICTURE SLEEP LIGHT ON, REPLACED C-500 Set has high voltage. Sleep light is on, but set has nopicture. Found .7Vpp on IC-301/pin 31 (should be 2 volts).
SonyKV27XBR65
SHUTDOWN ON NO-SIGNAL STATIONS, READJUST THE HOR. FREQ. If unit was switched from active station to active station,everything was ok. If you used CHANNEL UP or DOWN and went to a no-signalstation, unit would shutdown.
SonyKV27XBR65
RGB VERTICAL LINES TOP OF PICTURE, SEE TVP SB # 76 Three to four retrace lines are visible at the top of thescreen. They do not look like ordinary retrace lines, but are of solidred, blue, or green colors.
SonyKV27XBR65
HORIZONTAL LINES IN PICTURE, REPLACED C-546 (IC-500/PIN 5) Horizontal lines in picture sometimes on top sometimeson the bottom. Looks like retrace but in reality it is ringing.
SonyKV27XBR65
NO PICTURE, HOW TO TROUBLE SHOOT THE IK CIRCUIT As you may have noticed, when servicing this and other unitsusing this particular IC-301, RGB lines at the IC level are blanked any-time the C board is disconnected. The main reason for this blanking isa cathode current detect line (IK). When the unit
SonyKV27XBR65
VERTICAL LINES ON BOTTOM OF SCREEN, REPLACED C-504 I have now seen several models, ANU-1 chassis that exhibitwhat looks to be an odd type of retrace at the bottom of the screen.There may also be a few lines missing in the middle of the screen. It isunlike vertical problems I have seen in the past. The


Assistência TécnicaAs dicas apresentadas destinam-se a técnicos de eletrónica, a tentativa de reparação ou assistência sem ter conhecimentos de eletricidade e eletrónica, podem provocar danos mais graves aos equipamentos e, devido a tensões muito elevadas em alguns circuitos, graves danos fisicos que podem constituir um risco em determinadas reparações.

Não arrisque reparar equipamentos com tensões elevadas se não tiver conhecimentos técnicos para o fazer em segurança.

Verifique se o esquema está disponível na área de downloads