Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CDXU300 | MECHANISM JAMS (FOUND M501 AND M502 WERE DEFECTIVE) | Elevator and loading mech work very slow you will notice ahum on audio. When you take the unit apart to test, unit works fine. Ifyou measure voltage from power supply to mechanism chassis when loadinga disc you measure 4.5v. If you connect Unilink gro | ||
Sony | CDXU300 | PART # CORRECTION: SW654 | Service manual correction # 1, page 4, shows a picture ofSW654 used in some production, but the part number listed is for theswitch used in previous production. The switch in the drawing contains anadditional spring-steel switch actuator which is not fo | ||
Sony | CDXU300 | DAMPERS LEAK | Since early '93, 6 leaking dampers have been found. All havebeen located at the right rear of the unit. | ||
Sony | CDXU300RF | DISC JAMS (REPLACED BROKEN GEAR, REF. 112, P/N 3-364-432-01) | When disc is returned to magazine from play position, sliderassy #115 is not driven and disc doesn't return fully. | ||
Sony | CDXU300 | DISC JAMS (REPLACED BROKEN GEAR, REF. 112, P/N 3-364-432-01) | When disc is returned to magazine from play position, sliderassy #115 is not driven and disc doesn't return fully. | ||
Sony | CDXU300RF | INTERMITTENT POWER ON - REPLACED DEFECTIVE IC401 | Power would come on intermittently, found reset IC would have5v at pin 1 and wouldn't at times. | ||
Sony | CDXU300RF | WON'T PLAY, ELEVATOR JAMMED (RE-ALIGNED BENT CHASSIS) | MD elevator mech. jammed, would not raise. Found chassisbent near front damper. The X-Lever Assy was hitting chassis. | ||
Sony | CDXU300 | UNIT WILL NOT LOAD CD'S IN VERTICAL POSITION | While in horizontal position, unit would load and playnormally, but when moved to vertical position, it would not load CD's. | ||
Sony | CDXU300 | ONE CD LEFT IN THE CHANGER WHEN MAGAZINE IS EJECTED | Unit came back, after it was modifed, with one CD stuck insidethe changer after the magazine was ejected. -HQ COMMENTS: Tokyo has informed us that this problem may be caused byany of the following reasons: the magazine vibrates in the magazinecompartmen | ||
Sony | CDXU300 | NO FUNCTIONS (REPLACE X601, P/N 1-577-273-11) | Unit would not operate or even reset. Observed that LED forDPT sensor would not turn on. Found that crystal X601 was not supplyingsignal to IC601. | ||
Sony | CDXU300 | CD DOES NOT PLAY WHEN UNIT MOUNTED VERTICALLY | Unit accepts CD but will not lock down onto spindle motorplate in vertical position. The D.H. spring becomes bent which allows thedisc to ride on top of plastic guide and not lock properly. | ||
Sony | CDXU300 | UNIT JAMS, DISCS NOT RETURNED FULLY TO MAG. (REPLACE SW655) | Unit would load disc, but then when you went to change disc(for example: from 1 to 5) the slider assembly would not return previousdisc all the way in to magazine. Thus, when the elevator went up or down,the disc would hang up on the elevator assembly. | ||
Sony | CDXU300RF | UNIT JAMS, DISCS NOT RETURNED FULLY TO MAG. (REPLACE SW655) | Unit would load disc, but then when you went to change disc(for example: from 1 to 5) the slider assembly would not return previousdisc all the way in to magazine. Thus, when the elevator went up or down,the disc would hang up on the elevator assembly. | ||
Sony | CDXU300 | NO POWER/PLAY; SHUTS DOWN HEAD UNIT (REPLACE D653) | When a CD changer is connected to control unit (XR-U200,XR-U330, etc.) control unit shuts down completely and has no power, evenwhen reset. CD changer goes through its reset process, but will not loador initialize CD's. | ||
Sony | CDXU300RF | SKIPPING WHEN VEHICLE MAKES TURNS (REPLACE OMD CHASSIS ASSY) | The CD player would skip only when the car would go aroundturns. The problem is caused by wobbling of the spindle motor. |