Dicas Reparação
Modelo - Chassis CDXA30
Pesquisa: CDXA30 Enviar Dica Resolvida
Resultados 18
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CDXA30 | POPPING NOISE BETWEEN DISCS (REPLACED Q303 ON JACK BOARD) | As unit changed discs, a popping noise ocurred at the outputs.I checked all muting lines and they seemed to be working normally, until Ichecked the muting relay, which was not energizing. | ||
| Sony | CDXA30RF | REMOTE UNIT NOT AVAILABLE FROM NPC | The RMX1F is the wired remote control and RF unit for theCDXA30RF. If the customer should lose the remote unit or should it getbroken (see page 23 of Service Manual) there is no part number for theremote unit. The PC board does not come with parts on it | ||
| Sony | CDXA30RF | PART NUMBER CORRECTIONS: ANTENNA JACK AND ANTENNA PLUG | The part number for the antenna lead is incorrectly listed inthe service manual. The part received is key top, a complete button.What is he correct part number. -HQ COMMENTS: The correct part number for the antenna plug is9-996-065-01. The part number | ||
| Sony | CDXA30 | UNIT SENSITIVE TO SHOCK (USE NEW DAMPERS, P/N 3-355-772-01) | It seems that the dampers are extremely stiff, which causesskipping. Found that the dampers used in CDX-A15 are softer. | ||
| Sony | CDXA30RF | PART # ADDITION: PLUG HOLDER (PART OF REMOTE COMMANDER CORD) | The service manual is missing the part number for the plugholder at the end of the remote commander cord. | ||
| Sony | CDXA30RF | UNIT DOES NOT RESET OR EJECT | Unit would not reset, no elevator motor or eject. | ||
| Sony | CDXA30 | INTERMITTENT PLAYBACK, SLED DRIVE, AND CLV DRIVE | When powered up, unit would load and play disc correctly.After putting unit in standby or after a reset, unit would load a disc butnot home sled, spin, or play a disc. | ||
| Sony | CDXA30 | DISCS JAMMING IN THE XA-10B | Have received numerous complaints of discs jamming in XA-10B.Problem usually appears to be discs made off-spec (i.e. slightly thickerthan normal and having rough edges, so they fit too tight in XA-10B). Themost common brand of discs with this problem is | ||
| Sony | CDXA30 | WILL NOT LOAD DISC - ROLLER SLIPPING ON SHAFT | The disc will not be pulled out of the magazine. It will alsonot be pushed back in. The disc is engaged with the rollers, but theroller is slipping on the metal shaft. | ||
| Sony | CDXA30 | UNIT WILL NOT LOAD DISC | Unit will not load disc, elevator will not come down. E-99shows on display. | ||
| Sony | CDXA30 | NO PLAY | If replacing RF board on unit, there will still be no play. | ||
| Sony | CDXA30 | REVISION OF SERVICE BULLETIN NUMBER CAR0130 | The service bulletin tells you to connect pins 3 and 7 in theRMX2 to cure the distorted audio but in most cases the customer usuallysends in the CDX-A30 and not the RMX2. | ||
| Sony | CDXA30 | UNIT IS DEAD - NO MOTION - IC502 | Unit is dead - no motion. Will not reset. | ||
| Sony | CDXA30 | UNIT WILL NOT PLAY THE DISC | Will not play disc. Found 1.0V DC on negative side of DD1(DC-DC Converter). Checked for short between outputs and Grd all OK.Installed new DD1 anyway and tested operation. Unit played for 1-2 min.and then DD1 failed again. Removed CNJ2, CNJ1, CNJ4, a | ||
| Sony | CDXA30 | BALANCE RING FOR CD CAUSE IT TO JAM WHILE LOADING DISC. | Disc will jam if owner has affixed adhesive balance ringaround it's circumference. -HQ COMMENTS: The balance ring on the outside edge of the disc causeit to catch on the roller, as it's thickness is increased. It can alsoprevent it's slipping onto the |