Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CDXA10 | DISCS JAMMING IN THE XA-10B | Have received numerous complaints of discs jamming in XA-10B.Problem usually appears to be discs made off-spec (i.e. slightly thickerthan normal and having rough edges, so they fit too tight in XA-10B). Themost common brand of discs with this problem is | ||
Sony | CDXA100 | WILL NOT WORK WITH RMX-2 | Will not work with RMX-2. E04 error display shows. Alsopertains to serial number 103051. | ||
Sony | CDXA10 | COMMANDER HOOK-UP | When using your bench test commander, replace the unit'sexisting cord (P/N X33295361), which is about 15 feet long, with the cordfrom an RMX2 (P/N 1-559-687-11), which is about 1 foot long. This makesworking on CDX-A10s easier. The cords are interchang | ||
Sony | CDXA10 | BALANCE RINGS FOR CD'S CAUSE CD TO JAM WHILE LOADING DISC | Disc will jam if owner has afixed adhesive balance ring aroundit's circumference. -HQ COMMENTS: The balance ring on the outside edge of the disc cause itto catch on the roller, as it's thickness is increased. It can alsoprevent it's slipping onto the t | ||
Sony | CDXA10 | NOISE AFTER PERFORMING UPGRADE | Servicer performed upgrade as per service bulletin No. 135.He now reports that unit is noisier. Any other feedback on this? -HQ COMMENTS: We have not had any negative feedback. Is it possible hedid something wrong? | ||
Sony | CDXA10 | CNP901 LINE OUT CABLE | Cannot identify part number for cable between Jack Board andMain Board. Two versions - older units (serial No. 17627) have a single8-pin connector for the Jack Board and dual 3-pin (5-pin connectors) forthe Main Board. Newer units (serial No. 22395) ha | ||
Sony | CDXA10 | E04 ERROR MESSAGE | Symptom of E-4 error message only when mounted in car. Unitworked fine on bench. | ||
Sony | CDXA10 | SYSTEM CONTROL WOULD LOCK UP | Unit's system control would LOCK-UP with volume on high.No controls operative. | ||
Sony | CDXA10 | CAR STEREO SERVICE BULLETIN #73 (CDXA10 DISC PACK) | Disc pack can be safely and easily removed in 5 secs followingmy procedure rather than following S/B #73 (car stereo). Use a flatobject (I use a straightened stainless steel clasp senior - made in Japan.This clasp can be obtained at any stationery store | ||
Sony | CDXA10 | E-99 DISPLAY - NO OPERATION | E-99 display. Mechanism would not reset. No operation withmagazine inserted. | ||
Sony | CDXA10 | INCORRECT PART NUMBER - IC1001 | Incorrect P/N 8-759-908-95 Correct P/N 8-759-937-35 -HQ COMMENTS: We have already issued a S/B on this. It is now beingprinted and should be out shortly. | ||
Sony | CDXA10 | UNIT TRIES TO LOAD TWO DISCS | The customer complained that the unit would periodically jam.We found that one disc (David Sanburn/Voyeur/Warner Bros 3546-2) made byPolygram in West Germany was causing the problem. | ||
Sony | CDXA10 | NOISE IN BACKGROUND WHEN DISC IS STARTED | There is an audible noise present when a disc is runningeven though the output is supposed to be muted. This also occurs when theunit is in the pause mode. I believe the noise is being generated by thespindle motor. Has anyone else reported this probl | ||
Sony | CDXA10 | NO REMOTE FUNCTION | We have seen a few units at the SSC now with the problem ofno remote function. |