Dicas Reparação
Modelo - Chassis CDX65
Pesquisa: CDX65 Enviar Dica Resolvida
Resultados 15
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CDX65 | ERASING ALL DISC TITLES AT ONCE (CUSTOM FILE) | The CD changer may not display NO DATA after servicebulletin #330 has been executed. | ||
| Sony | CDX65RF | PART AVAILABILITY: HIDEAWAY/WIRED DISPLAY | The manual has no part number for Hideaway units and WiredDisplays that are defective and cannot be repaired to component level. | ||
| Sony | CDX65RF | SKIPS WHEN PLAYING OUTER TRACKS (SEE BULLETIN 358R2 FOR FIX) | The unit skips when playing the outer (higher number) trackson the disc. | ||
| Sony | CDX65 | SKIPS WHEN PLAYING OUTER TRACKS (SEE BULLETIN 358R2 FOR FIX) | The unit skips when playing the outer (higher number) trackson the disc. | ||
| Sony | CDX65 | SCREW USED IN SB 358R1 UPDATE STRIPS AND BECOMES LOOSE | SB update # CAR 0358R1 calls for a screw part 7-621-255-01, tobe used to hold down the new cover in the bulletin mentioned. However, Ifound that this type screw strips when installed, which becomes loose.The screw is machine type thread. | ||
| Sony | CDX65RF | COMPRESSION SPRING MISSING | Mechanism jammed and discs are stuck inside. Found that thecompression spring (ref. 61) was not in the unit. | ||
| Sony | CDX65 | SERVO PCB INCOMPATIBILIITY | After replacing SERVO PCB there is no elevator & no load/save. | ||
| Sony | CDX65 | RESETS WHEN POWERED UP, WON'T DO ANYTHING ELSE | Unit will reset when powering up but won't do anything else.Inspecting further, data line and clock line won't go high.Data line and clock line were shorted with each other. In closeinpection, found a copper strand from wire inside unilink connector CN8 | ||
| Sony | CDX65 | WON'T RESET WHEN POWERED UP (REPLACED SW902,Q903,D905,D906) | Unit won't reset when powering the unit. If you load themagazine it will reset but won't do anything else. Inspected MD boardQ903 was overdissipated, found SW902 was shorted. -SOLUTION Replace SW902 1-692-864-11, Q903 8-729-808-01, D9058-719-105-99, | ||
| Sony | CDX65RF | 1 DISC NOT EJECTED (REPLACED REF. 60 AND REF. 205) | Unit came in with one CD stuck inside. Looks as if cust triedremoving all discs but one. Noticed MD assy was not chucked down. Resetunit and unit ejected disc, but when attempt to play disc elevator stopsmoving but you could hear that the elevator mot | ||
| Sony | CDX65RF | DOES NOT LOAD CD'S; MAKES NOISE (FOUND REF. 221 DAMAGED) | Customer complaint: constantly will not play. Open unit tocheck, found does not take any CD into roller. #164 slide lever and 221gear made noise when trying load discs. | ||
| Sony | CDX65RF | PART # CORRECTION: Q503 (CORRECT PART # IS 8-729-204-10) | Found part # for Q503 8-729-240-10, was not in system (FIPM).Looked in semi-conductor replacement handbook and found that the # for2SD1417 is actually 8-729-204-10 (page 700 of 1992 2nd SRM). We had thepart in stock and the unit was repaired. | ||
| Sony | CDX65 | DOES NOT LOAD CD'S; MAKES NOISE (FOUND REF. 221 DAMAGED) | Customer complaint: constantly will not play. Open unit tocheck, found does not take any CD into roller. #164 slide lever and 221gear made noise when trying load discs. | ||
| Sony | CDX65RF | CONTROLLER'S DISPLAY SHOWS "FULL" WHEN ENTERING TITLES | The changer controller's display may show FULL when tryingto enter disc titles, even though the customer has not yet entered themaximum of 110 disc titles. This problem occurs because some units didnot have the factory-entered titles erased before they | ||
| Sony | CDX65 | CONTROLLER'S DISPLAY SHOWS "FULL" WHEN ENTERING TITLES | The changer controller's display may show FULL when tryingto enter disc titles, even though the customer has not yet entered themaximum of 110 disc titles. This problem occurs because some units didnot have the factory-entered titles erased before they |