Dicas Reparação
Modelo - Chassis CDPC900
Pesquisa: CDPC900 Enviar Dica Resolvida
Resultados 13
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CDPC900 | WILL NOT LOAD DISC - REPLACED D902 | Everything worked normally except the rollers would not turn.IC903 voltages seemed normal except when the rollers should be turningIC903 was not suplying voltage to M602 load motor. | ||
| Sony | CDPC900 | CNP101 AND CNP102 HARNESSES | FPR#O2538 identified the part# (missing from service manual)as #1-946-072-26. Servicer reports part supplied under this part # is tooshort - about 3 long. Should be about 7 long. -HQ COMMENTS: Use P/N 1-690-235-11 for CN101 (approx. 8). Use P/N1-690-2 | ||
| Sony | CDPC900 | PART # INFO, OPTICAL PICKUP HARNESSES (P/N 1-946-072-21) | The part numbers for the harnesses from the pick-up assemblyto the main board CNP101 and CNP102 are missing from the service manual. -HQ COMMENTS: The National Parts Center has researched the part numberand informed us that the part number is 1-946-072- | ||
| Sony | CDPC900 | WON'T READ TOC AND CD IS EJECTED BACK INTO MAGAZINE | CD would load, spindle would move in counter clockwise direc-tion. CD would be ejected into magazine. Noticed pin 44, IC-201 was highand pin was 45 low. | ||
| Sony | CDPC900 | PART NUMBERS FOR BUSHING AND CLIP NOT REFERENCED IN S/M | Shaft 169 on page 27 of service manual fits through a smallplastic bushing that I've drawn in the accompanying service manual pageand the shaft is retained by a plastic clip that I've circled. No partnumbers. Servicer says that there was no grove at th | ||
| Sony | CDPC900 | INCORRECT PART NUMBER FOR ESCUTCHEON REF. 190 | The part number for the Escutcheon (Ref.190) listed in theservice manual is incorrect. The incorrect part number is X-4917-726-2. | ||
| Sony | CDPC900 | WON'T COUNT IN FAST FOWARD SCAN | When you Fast Foward Scan, unit stops counting and appears tomove forward faster than Reverse Scan which works ok. -HQ COMMENTS: We would recommend checking pin 20 of IC-201 with youroscilloscope. Look at the output to the sled motor drive chip (IC-202 | ||
| Sony | CDPC900 | DISCS JAMMING IN MAGAZINE | Disc gets jammed in unit. Removed and realigned - checkedoperation of unit. Transport appears all ok. After a week to 10 days,unit comes back with same problem. | ||
| Sony | CDPC900 | CD WILL NOT RETURN TO MAGAZINE | Frequently, but intermittently, the discs will try to returneither above or below the correct slot, jamming the magazine. Noadjustments on this model. This is the 5th or 6th unit this ASD hasreceived. | ||
| Sony | CDPC900 | DIRTY FOP LENS CAUSING SKIPPING | In this particular unit the complaint was continuousshuffling. Unit could not lock on to discs in the shuffle mode. Theoptics were completely hazed over (not cloudy as in the new 150s). I haveseen this in other CDP-C900s and CDP-C15ESDs. It has also | ||
| Sony | CDPC900 | WILL NOT LOAD DISC | There is a lot of free play in roller and brass bushing.Eventually, the gear that drives the roller comes out or the bushing fallsout or both. | ||
| Sony | CDPC900 | JAMMED STATE - DISCS WITH ROUGH EDGE | Unit came in for repair on 4 occassions in a jammed state.Certain discs with a very rough edge tend to jam as they are inserted backinto the cartridge after being played. The rough edge had flacking orhair like particles on the edge and was purchased fr | ||
| Sony | CDPC900 | NO PART NUMBER - CLIPS FOR PLASTIC BUSHINGS FOR WORM GEARS | There is no part number listed in the service manual for theclips which hold the plastic pieces which ride on the worm gears of theelevator assembly -HQ COMMENTS: The part number for the clips is 4-926-216-00. |