Dicas Reparação
Modelo - Chassis CDPC335
Pesquisa: CDPC335 Enviar Dica Resolvida
Resultados 13
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CDPC335 | WHISTLING NOISE - ADD RTV BTWN SPINDLE MOTOR & BD BOARD | A whistling noise (about 400HZ) manifests itself on certaincuts of disc (Goodbye Yellow Brick Road, Elton John, Polydor D103076). Ifyou touch the optical block lightly, the noise disappears. | ||
| Sony | CDPC335 | TRAY MOTOR NOT LABELED OR WIRED CORRECTLY | After replacing the tray motor with a new one the playerwould not work correctly, the tray would rotate back and forth and notrecognize the cd in the unit. | ||
| Sony | CDPC335 | BROKEN POST FOR LEVER REF #111 - SEE S/B HFP 365 | Post for set lever ref #111 breaks from chassis causingdrawer problems. | ||
| Sony | CDPC335 | SKIPPING DURING EXCHANGE - REPL SYSTEM CONTROL IC401 | Unit would mute during exchange cycle. Not sort ofmuting/skipping associated with focus or tracking problems. Muted for 30secs, installing new system control cpu resolved problem. Unit did nothave problem with BU alignment wich requires cpu to be ch | ||
| Sony | CDPC335 | TRAY MOTOR SPINNING BACKWARDS - REPLACE TABLE MOTOR | Ran into this problem 5 times in past 3 weeks. Removed traymotor. Old motor is installed with lable on motor facing up. If newmotor is installed with lable facing up, motor will spin backwards andtray will not function properly. | ||
| Sony | CDPC335 | SHIPPING LABEL RECOMMENDATION | Some units come in with FOP sled ass'y jumped off track.Not following shipping instructions from manual. | ||
| Sony | CDPC335 | NOISE ON LOUD PASSAGES - IC501 DEFECTIVE | Crackling during loud sound passages. More apparent usingtrack two of YEDS-18. Input pins of IC clear of distortion. At the outputpins, the signal was clipped and oscillating. -HQ COMMENTS: IC501 is the line amp/muting att. | ||
| Sony | CDPC335 | BU UNIT HITS DISC TABLE WHEN CHUCKING | On 2 different units the laser hits the disc table whenchucking. It appears disc table, ref# 59, is stopping too far clockwise.The pin on ref# 123 is against the left side of the slot in ref# 59. Isthere any adjustment? What makes the table stop in th | ||
| Sony | CDPC335 | JAMS DISC TABLE, WON'T PLAY DISCS - REPLACE GEAR 61 AND 66 | Unit will not play discs. BU assembly won't come up, due tointerference with disc table. Occasionally, the CLV motor pulley isdamaged. -HQ COMMENTS: To repair this problem as per Tokyo: Replace IC 401 withP/N 8-752-849-42, also verify values of R457 (2. | ||
| Sony | CDPC335 | CORRECT ALIGNMENT OF DISC DRAWER DURING REASSEMBLY | Supp. #1 does not mention how to properly resinstall the discdrawer assy. | ||
| Sony | CDPC335 | BROKEN POST ON CHASSIS - REPLACE CHASSIS | Chassis post broken off used for ref. 3 (lever set). | ||
| Sony | CDPC335 | NO OPTICAL PICKUP FUNCTIONS (RESOLDER CN101 AND CN102) | Laser of CDP-C235 would not turn on, no focus, and opticinoperable. There was no +5V on pin 7 of CN101 or pin 5 of CN102. | ||
| Sony | CDPC335 | TRAY OPENS AND CLOSES BY ITSELF (ALIGN CAM MECHANISMS) | The tray opens and closes by itself, the FOP mechanism islocked in the up position. |