Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CDPC245 | TRAY MOTOR NOT LABELED OR WIRED CORRECTLY | After replacing the tray motor with a new one the playerwould not work correctly, the tray would rotate back and forth and notrecognize the cd in the unit. | ||
Sony | CDPC245 | TRAY MOTOR SPINNING BACKWARDS - REPLACE TABLE MOTOR | Ran into this problem 5 times in past 3 weeks. Removed traymotor. Old motor is installed with lable on motor facing up. If newmotor is installed with label facing up, motor will spin backwards andtray will not function properly. | ||
Sony | CDPC245 | DISC TABLE WON'T STOP - REPLACED M801 | Disc table rotates continuously and cd player wont' detectdiscs. Replaced flex cable and checked D801 sensor, player is still doingsame thing. | ||
Sony | CDPC245 | INTERMITTENTLY DOES NOT RECOGNIZE DISCS | Intermittently, unit will not recognize disc. Occurs inshuffle mode or checking discs. Unit will load and chuck discs w/oproblem. No problem with alignment as describe in SB CSA13/#390.Turntable appears to rotate a bit too fast. Logic from disc sen | ||
Sony | CDPC245 | NO AUDIO | Had no audio output on either channel. Found input to line amp Ic501 only showing a small sawtooth wave in. | ||
Sony | CDPC245 | INTERMITTENT/ERRATIC OPERATION - REPLACE BD BOARD | Several problems recently relating to the units abilityto read and track the disc. The problems are often intermittent anderratic. in these instances the problem has been isolated to poor feedthrough connection on the Bd board. There does not seem to b | ||
Sony | CDPC245 | KSS240 BD BOARD, WRONG # | When this board is ordered A4649433A to compliment the KSS240optic it is the wrong board for this unit. There is no IC102 on the Aside of the board. There is a totally different CN101 connector. Canyou please explain why/send the correct board # -H | ||
Sony | CDPC245 | HUMMING NOISE FROM MACHINE - ADD WEIGHT(S) TO BU ASSY | As per SBHFP0381, stated to add weight and screw to optic toeliminate noise. Works for some but not all. Noise originated fromspindle motor assy X49175233. Hot glued to 2 weights 496297901 toleft hand rear side of BU assy I cannot determine if this is | ||
Sony | CDPC245 | NO OPEN/MECH NOISE - CD MECH STUCK AGAINST TABLE | Unit open and makes mech. moise. After opening case foundCD mech stuck with table B. | ||
Sony | CDPC245 | NO OPEN - SET LEVER BROKEN | Unit not opening the tray. Troubleshooting found gear is misaligned with tray table. After removal of table tray visual inspectionfound lever, set is broken. | ||
Sony | CDPC245 | DISK SKIPS INT. - REPL GEAR REF 66 | Table would try to move and then would stop. found gearref# 66 had teeth bent or worn. | ||
Sony | CDPC245 | DOOR WOULDN'T CLOSE | Door would not close all the way in and wouldn't play.Found main gear out of time. Also found post broken off chassis. | ||
Sony | CDPC245 | ERRATIC OPERATION, NO SLED - RESOLDERED SLED MOTOR LEAD | The sled would not operate which caused a vierty of symptomsdepending on whether or not the limit switch was closed. (limit switchmust be closed for proper loading). | ||
Sony | CDPC245 | DISC TABLE ROTATES SLOWLY - REPLACED ROTARY GEAR | Disc table rotates slowly. | ||
Sony | CDPC245 | MISSING PART - INSTALLED MISSING TENSION SPRING | Lock lever will not engage (stay put), tension spring wasnever installed in unit. |