Dicas Reparação
Modelo - Chassis CCDV5
Pesquisa: CCDV5 Enviar Dica Resolvida
Resultados 64
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CCDV5000 | VERY DISTORTED REC. PICTURE/REPLACE C-451, PC-35 | The unit will play pre-recorded tapes with some noise. Ireplaced the video head and playback was fine for pre-records but it wasstill very noisy for self-recordings. I found pin 7/CN-303 at about 0.9vinstead of 4.9v which was caused by a leaky C-451- s | ||
| Sony | CCDV5000 | BAD PB PICTURE- NO LUMINANCE | In PB mode, the video out contained no Y signal. I traced itto pin 23 of HD-8 board on VI-66 board and there was a good signal. Then,I checked for output on pin 20 of HD-8 board and found noise. I checkedpin 20 of comb filter IC on HD-8 and found nois | ||
| Sony | CCDV5 | IRREGULAR TAPE MOTION/HARDENED GREASE ON TENSION ARM | The unit showed several problems such as eating tapes, tapepath problems and sometimes eject problems. The grease on the tensionregulator arm hardened and caused the arm to hang up at differenttensions. This caused different back tensions which caused | ||
| Sony | CCDV5000 | AUTO FOCUS QUESTION | We need to know at what point the auto focus sets the lens ata fixed point when in wide angle zoom. We cannot locate this informationin the service or owners manual. Are we overlooking it or does this modelhave a different mode of operation?? Please l | ||
| Sony | CCDV5000 | NEW AUDIO/PCM PC BOARD VERSION INCOMPATIBILITY/SM SUPP-1 | Instead of PC-35, we found a different version PC-52, withcustomer complaint as huming noise as in manual mode, even with and levelcontrol at minimum setting (0) level. The circuit is different withPC-35. Replaced with PC-35 that solved the hum. All a | ||
| Sony | CCDV5000 | NO COLOR GAIN | Weak, light color no yellow color only. If view with colorbar test chart no AWB or manual white balance function. | ||
| Sony | CCDV5000 | DISPLAY FLASHES | Display is ok in Stop mode. Switch power to VTR mode anddisplay starts to flash (as if no lithium battery). No noticable currentdraw on external power supply. | ||
| Sony | CCDV5000 | DATA SCREEN SCRAMBLED ONLY IN VTR WITH NO SIGNAL | CV-401 AFC trimed will correct data screen then it would startto drift. Voltages around IC-406 AFC capacitor pin 37 and up areincorrect. AFC input is UCC. Replaced CV-401. -HQ COMMENTS: CV-401 is the AFC adjustment element for the DDS SyncGenerator I | ||
| Sony | CCDV5 | DISTORTED SUPERIMPOSE | E-E picture had no color and superimpose had undefinedcharacters scattered over the picture area. Superimpose buttons had noeffect (Date/Time missing). Found D+ and 5V at CN-252 pin 5 was low. | ||
| Sony | CCDV5000 | LCD FULLY LIT UP - INTERMITTENT | Sometimes by squeezing or flexing the cabinet all segments ofthe LCD would go on or sometimes the deck would even go into Rewind. Ifthe unit was disassembled, it would not fail. I notied that one cabinetscrew would connect the handle bracket (Ref. No. | ||
| Sony | CCDV5000 | UNIT MUST BE DISASSEMBLED TO ADJUST EVR | Unit needed EVR adjusted several times to satisfy a very de-manding customer. Unit had to be disassembled each time adjustments weremade to ground TP B6. | ||
| Sony | CCDV5000 | NO AUDIO - ONE OR BOTH CHANNELS | No audio output on left channel. Traced to no output but goodinput to audio output selector IC-317. Found C-382 had one lead pulledout of can. Noticed that all four capacitors along side of IC-317 werenot flush mounted to board. | ||
| Sony | CCDV5000 | "WAVY" LINES AT 2-4 SECOND INTERVALS IN PB WHEN RECORDED | After 30 minutes, Playback would show slight wavy lineshorizontally at 2 - 4 second intervals. This problem only exists on tapesrecorded on this unit. Playback of tapes from other units were perfect. | ||
| Sony | CCDV5000 | PART NUMBER FOR REC PROOF SWITCH TAPE SELECT | There is no part number listed for the REC proof switch onthis model. What is the part number? | ||
| Sony | CCDV5 | NO CAMERA VIDEO | No camera video, zoom and AF work ok. Camera video present onV4-8 pin 54, not at pin 3. Checked for +5 volts on VY-8 board - notthere. |