Dicas Reparação
Modelo - Chassis CCDTR5
Pesquisa: CCDTR5 Enviar Dica Resolvida
Resultados 146
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CCDTR5 | BLUE SCREEN IN CAMERA MODE/OPEN TRACE BETWEEN R328-L302-VC60 | Solid blue screen in camera mode. | ||
| Sony | CCDTR5 | SERVICE BULLETIN NUMBER CAM0171 - ORIGINAL SCREWS TOO SHORT | When performing service bulletin No. CAM0171, and installingthe new base block assembly the original mounting screws are now tooshort. | ||
| Sony | CCDTR51 | NO CAMERA PICTURE AFTER WARM UP | After warm up, camera picture fades out to black with streaksfrom left to right. The VCR Playback is ok. | ||
| Sony | CCDTR51 | SHORTED C-154 ON "VS-77" BOARD | Unit is inoperative. | ||
| Sony | CCDTR5 | WON'T ACCEPT TAPE | Unit would eject but immediately produce a caution light.Load motor would not cycle correctly once eject was completed andeventually the unit would load without depressing the door compartment. Atechnician had previously replaced the CPU IC-601 but this | ||
| Sony | CCDTR55 | NO LUMINANCE | Although offshore model, information applies to our CCD-TR55.Symptom of no luminance. Chroma slightly visible. Voltage at pins 36 and38 of IC-301 read a low .9V. | ||
| Sony | CCDTR5 | BROKE PART INSIDE OF LENS ASSEMBLY | Camera seems normal (no physical damage) but some zoom partfell off from lens assembly. Some weakness? -HQ COMMENTS: We are not aware of this kind of weakness. Perhaps thecamera was dropped on a carpet, with the lens pointing down. | ||
| Sony | CCDTR51 | NO CAMERA VIDEO | No camera video. IC-707, pins 86 to 95 appear to have gooddata input. No luminance signal out at pin 51. VDD and clocks measureok. | ||
| Sony | CCDTR51 | NO LCD DISPLAY OPERATION | No LCD display operation. Crystals X-241 and X-242 wereoperating correctly. | ||
| Sony | CCDTR5 | SHUTDOWN IN RWD OR REV SCAN | This is the second new unit with this problem. All functionsare normal except unit will shut down in REV, SCAN or RWD. When thishappens, no functions will work until unit resets in four seconds or re-move battery to reset. | ||
| Sony | CCDTR5 | SCREW FOR BASE (3) ASSEMBLY, GUIDE RAIL | Refer to CCD-TR5 FPRs No. M0215 and K1192. The numberA-7040-154-A chassis block assembly mechanical is now substituted with a-P. When installing the old (Ref. No. 309) base (3) assembly guiderail, one of the two (Ref. No. 319) screws will have to be re | ||
| Sony | CCDTR5 | CAUTION LIGHT COMES ON DURING REWIND | Noisy erratic rewind because the tape became slack in the tapepath. The RM95 displayed 00.03 service mode error. No error was shownduring unthreading. Determine multiple damaged teeth on arm assemblygear. Installed No. 256, 264, 207 and 206. This re | ||
| Sony | CCDTR5 | PART NUMBER FOR CAPSTAN MOTOR CONNECTOR | The service manual does not call out the connector for thecapstan motor as a separate part number and the FP-182 board does nothave the connector attached. -HQ COMMENTS: The part number for this connector is 1-565-662-11 andit is registered in KCP. | ||
| Sony | CCDTR5 | TICKING NOISE FROM MECHANISM | Heard ticking noise coming from the mechanism in all modes. | ||
| Sony | CCDTR5 | LS CHASSIS ASSEMBLY SUBS TO NEW PART NO. WHICH DOESN'T WORK | Ordered part number X-3727-953-2 and was sent X-394-018-61.Unable to install new part. -HQ COMMENTS: Refer to service bulletin CAM 221. This must be donewhenever the cassette compartment holder is changed. |