Dicas Reparação
Modelo - Chassis CCDM8U
Pesquisa: CCDM8U Enviar Dica Resolvida
Resultados 45
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CCDM8U | VERY INTERMITTENT CAUTION LIGHT/REPLACE FP8 | After changing tapes and after eject, unit would only recordfor a few seconds. Suspected intermittent reel pulse. Replaced the photocoupler diode to no avail. | ||
| Sony | CCDM8U | AFTER RECORDING, WOULD PLAYBACK, NO CAPSTAN LOCK AND LP | After the symptom occured, I attempted an adjustment for ATFrecord current. Page 73, 3-3-3 pin 1 of RP29 board did not have a signal.I traced into the camera block and found an open connection on the FP5flex cable. | ||
| Sony | CCDM8U | ONLY WORKS WITH ACP-80UC OR EXT SUPPLY | When unit was powered with power supply at 8 volts DC,operation was normal except for unstable drum. When supply was turneddown to 7.5VDC measured at terminals, unit would quickly unload the pinchroller and shut down. The 5 volt to micro was ok as per | ||
| Sony | CCDM8U | UNIT WILL NOT LOAD- POWER LED FLASHES | Unit will not load or unload. | ||
| Sony | CCDM8U | NO CAMERA VIDEO IRIS IS OK | Unit had no record Y signal. Signal out of pin 15 of the ED11(Rec Y) was not there. Tried to inject video from a generator and foundED-11 board shorting out signal. Lifted pin 15 of the ED-11 board toconfirm the problem. | ||
| Sony | CCDM8U | DOES NOT RECORD VIDEO | Unit records audio. Does not record video. | ||
| Sony | CCDM8U | NO RECORD COLOR | No color recording from camera section. | ||
| Sony | CCDM8U | COLOR BARS IN PICTURE | Color bars in picture after recording. | ||
| Sony | CCDM8U | CAPSTAN MOTOR WILL NOT TURN | X-201 had DC voltage on each side. X201 was not oscillatingproperly. Waveform was a bunch of distorted pulses when ejecting. Drumwould also chatter. | ||
| Sony | CCDM8U | DRUM SPEED FLUCTUATES | Drum speed varied constantly. Picture looks like it isbreathing. | ||
| Sony | CCDM8U | CC-3 BOARD AVAILABILITY | Is the (CC-3) board available? -HQ COMMENTS: Yes, the (CC-3) board is part of the mechanical chassis.The part number is listed in service bulletin number VCR0298 (2/27/87). | ||
| Sony | CCDM8U | BATTERY LIGHT BLINKS - NO FUNCTIONS | Unit is dead except for flashing battery lamp. | ||
| Sony | CCDM8U | NEW CABINET AND EJECT SWITCH | Unit would not eject. Installed above part six weeks ago.This cabinet assembly will not work with old style side frame (Ref. #110,pg. 124) which has hole, due to position of eject switch. Eject switchbends out of position and will no longer work. | ||
| Sony | CCDM8U | THERE ARE TWO MISTAKES IN CAMERA ADJUSTMENT MANUAL | 1-9 AGC setting adj. 1-21 Aperture adj.Test point in S/M VC-5 board TP810 ME-1 board TP711Correct test point VC-4 TP685 VC-6 TP952 -HQ COMMENTS: We are investigating this problem. | ||
| Sony | CCDM8U | EATS TAPES | Unit ejects half way then stops. Sometimes will eject buteats tapes. |