Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CCDF302 | NO COLOR IN PLAYBACK (FOUND CORROSION ON VA67 BOARD) | Unit played back video in black and white. | ||
Sony | CCDF301 | NO PIX FROM VTR, NO PB RF (FOUND OPEN TRACE ON SS100 BOARD) | When camcorder is in play mode, no picture. No RF on pin 3of CN508 (PBRF testpoint). Also missing was switching 5V (REC/PB) on pins11/12 of CN501 and pin 25 of IC506. Also missing was 5V on pin 27 ofsame IC. Found power line 5V open between L502 and | ||
Sony | CCDF301 | BAD REC/REPLACE C216 AND C240 | After rec from cam. pix looked bad. Too low Y and distortedY signal. After measuring rec. current discovered signal coming out ofIC206 pin 7. SW IC low. Found caps C216 and C240 def, leaky. C216 Part112660711 is not on the computer. C216 is 47ufx4 | ||
Sony | CCDF30 | PLAYS LP TAPES AT SP SPEED/REPLACE IC001 | Plays LP tapes at SP speed.Indicator on LCD is SP. Found defective IC 001 | ||
Sony | CCDF301 | UNIT GOES INTO EMERGENCY STOP IN PLAY AND FF | Unit would go into emergency shutdown in PLAY. Noticed thatthere was no take-up sensor signal. Replacement of the take-up sensor didnot cure the problem. | ||
Sony | CCDF30 | POOR SYNC ON MOST MONITORS, BUT LOOKS OK ON KV1311CR | On some monitors, such as PVM1354Q, pix had erraticor no horizontal and vertical sync. On KV1311CR, however, pix lookednormal. | ||
Sony | CCDF30 | DRUM WON'T INITIALIZE PROPERLY, CAPS FAIL C0068 SS BOARD | Drum won't start up properly, hesitates, or won't start up atall. I found C0068 3.3mf @ 50v to be the main culprit, but ususally I goahead and change C069.71.74, 75 which are all 10mf @ 16v. These 5capacitors area ll tied to IC004 'drum drive and seem | ||
Sony | CCDF30 | INT NOISE OR NO VIDEO IN P.B./NOISY RF C417 LEAKY | Noisy RF (PB) into IC360 pin 60, head amp caps previouslyreplaced, checked 5v supply to soft limiter circuit. Found C417 leaky. | ||
Sony | CCDF301 | CAMERA WILL NOT POWER UP/REPLACE DT77H HIC | Camera would shut down when attempting to power up. CheckedDC/DC no problem. Removed various supply voltages and found active shortacross -9v supply to CD58 RCB. Removed pin 40 of DT77H and unit no longershut down. | ||
Sony | CCDF30 | NO EJECT DUE TO NO DRUM START/REPLACE Q053, SS-86 BOARD | Unit never had any drum start so therefore didn't have anycapstan. When you go into eject in play mode the drum PWM start pluse outof pin 5 of IC001 would go from Ov to 5v. This pulse was input to thebase of Q053 turning the transistor on, but the coll | ||
Sony | CCDF301 | DATA TRANSFER FROM COMPUTER TO CAMERA STALLS ON ADDRESS 6 | When using the LANC jig to transfer data from the computer tothe camera, the program would fail with a communications error whenever itgot to address 6. This is a read-only location for the battery downvoltage adjustment. | ||
Sony | CCDF301 | LANC SOFTWARE 1-2.0 | When down loading to camcorder, software shows communicationserror when attempting page D address 06. SOLUTION: Eliminated data in computer for address 06 from file. Thislocation is read only and error will occur because computer cannot changethis da | ||
Sony | CCDF301 | NEED A WAY TO IDENTIFY 2 DIFFERENT LENSES USED | There are 2 lenses shown in the service manual. How do youknow which lens is which? -HQ COMMENTS: The two types are as follows: VCL-8508XE, part number1-547-422-11 (made by Canon) and VCL-8508XF part number 1-547-412-14 (madeby Koshina). You can identi | ||
Sony | CCDF301 | HOW TO DIFFERENTIATE LENS TYPES | There are two lens assemblies in the service manual. How doyou know which one is which? -HQ COMMENTS: There are two lens types - XE (1-547-422-11) and XF(1-547-412-12). The XE lens has the Sheet, F (REF #417) on the top of thelens. The XF has the sheet | ||
Sony | CCDF301 | NO MECHANICAL MOTION, X501 DEFECTIVE | There was no mechanical motion at all. The camera would powerup etc. but would not eject, record, play, etc. Mechanism control IC-501on SS136 had no clock and I found X-501 was defective. |