Dicas Reparação
Modelo - Chassis KV28WS2U
Pesquisa: KV28WS2U Enviar Dica Resolvida
Resultados 17
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | KV28WS2U | No sound, speakers pop out if volume is raised from zero. Audio output from Dolby A1 board at +5v dc. | Lightning damage to this set and connected VCR. Centre/surround amplifier IC shorted blowing IC protector to its negative rail. Both amplifier ICs replaced as a precaution. No damage to Dolby A1 board | ||
| Sony | KV28WS2U | OSD volume bar present continuously. No functions available | Front panel tactile switches leaky. Replace same | ||
| Sony | KV28WS2U BE3D | St/by LED flashes twice | M24C32 sm EEPROM replaced (caused by crt flashover?) | ||
| Sony | KV28WS2U BE3D | Service mode entering | from st/by press OSD/5/volume+/tv; TT____ will appear top right. Entering TT38 sets the TV as a 28 inch, TT24 sets TV as PAL I, TT79 for widescreen. MENU gives submenu choices eg geometry; TT00 exits & stores | ||
| Sony | BE-3D KV28WS2U | vol goes up or down on its own, channels wipe out of memory, unusual characters on LHS | int lockup of IC3, replace with new software type (IC3 TMS27PC0200-15 software 15FMBW706 or later, part number 875945310) | ||
| Sony | BE-3D KV28WS2U | no sound | D613 FMN-G12S o/c (871905838) | ||
| Sony | BE-3D KV28WS2U | no pic, sound Ok | no line drive, R870 1R 1W o/c | ||
| Sony | BE-3D KV28WS2U | int no remote | IR receiver IC900 894179051 | ||
| Sony | BE-3D KV28WS2U | buzzing on sound, IC260 gets hot | resolder earth pin on plug CN303 | ||
| Sony | BE3D KV28WS2U | St/by only LED flashes error code 2 | LOPTx can be cause, confirmed by measuring volts coll Q606 in prot cct. If it rises to 11v LOPTx faulty (should be 0v) - then enter serv mode & disable prot (see other entry). | ||
| Sony | BE3D KV28WS2U | St/by only LED flashes error code 2 | Instead of replacing the EEPROM try the following - Whilst LED is flashing enter serv mode (St/by, I, 5, vol+ & TV). This disables prot & set comes on with "TT--" . Press "0, 8" on R/C which will clear error buffer. | ||
| Sony | BE3D KV28WS2U | LED successively flashes twice | M24C32-MW6T EPROM IC2 - 8 leg sm device pt no 875952494 | ||
| Sony | BE3D KV28WS2U | LED flashes twice aft LOPTx replacement to cure dead set | Check EEPROM 24C32 in IF sound module by replacement. Enter service mode & at TT promt enter country code 24 (UK system) - prevents need for setting each chan band when tuning | ||
| Sony | BE3D KV28WS2U | EEPROM corruption | Caused by flashover of red gun in crt - crt replaced under warranty (if lucky) | ||
| Sony | BE3D KV28WS2U | Dead at sw on - will produce a click from relay after a period of time. When G2 advanced, line collapse noticed | Check for dry joints around scan coils plug, check R870M for o/c 1R, 1w |