Dicas Reparação
Modelo - Chassis
Pesquisa: Enviar Dica Resolvida
Resultados 81407
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | SLV620HF | DISPLAYS L04 ERROR CODE - REPLACE IC401 & PS401 | Push tape in will not eject, also reads L04 abnormal camrotation. | ||
| Sony | SLV620HF | UNIT DEAD OR INTERMITTENT FUNCTIONS - REPLACE C103 | This is the second unit received in two weeks with C103blown, pieces of plastic insulation found inside unit. Did you have anymore reports on this? | ||
| Sony | SLV595HF | INCORRECT PART NUMBER - CORRECT P/N IS 1-249-397-11 | In supplement 1 page 8 resistor R110 p/n is 1-249-497-11. | ||
| Sony | SLV595HF | INTERMITTENTLY, UNIT WOULD UNLOAD AND TURN OFF DURING PLAY | During play or record, unit would intermittently stop,unthread tape, and shut off. Since it looked like a power down reset,I tried a new power supply with no effect. Tried heating and coolingSYSCON IC, and was able to cause the problem to come and go. | ||
| Sony | SLV575UC | LOOKS LIKE CAP SPEED PROBLEM - REPLCD ARM ITEM # 279 | Looks like cap speed is off or not locking. Also, foundexcessive forward torque. | ||
| Sony | SLHF2100 | NO HI FI COLOR LINES IN PLAYBACK VIDEO | No hi fi audio, lines of chroma in playback video. Found PBAchin and PBB chin from RP35 board to AF55 board to be superimposed onthe AF sw pulse. | ||
| Sony | EVC3 | NOISE ON 1/4 BOTTOM OF PICTURE - REPLCD RP69(HEAD AMP) BOARD | Noise on 1/4 bottom of screen. RF envelope shows noise on topof the normal signal especially at the exit portion of each head reading. Found corrosion on RP69 board by IC2, most likely caused by C083, C043. | ||
| Sony | CCDTR5 | SWITCH BLOCK OFF STILL IN CAMERA MODE - Q621/VS-22 BD | unit came in with vtr/cam switch to off but still had e-e video.Tried swapping out switch block but that didn't fix the problem. I thenwent to the q603 and lifted the collector which shut down power. I put thepin back in then lifted the emitter -- s | ||
| Sony | TVP-GEN | SPECIFICATIONS FOR THE HEADPHONE JACK? | The Specifications for the headphone jack are missing fromthe S/M. -HQ COMMENTS: The specs. are as follows: Output Impedance: 47K Ohms Output Voltage: 500m Vrms (100% Modulation) | ||
| Sony | KV32HSR10 | NO PINCUSHION--CHECK Q505 SILKSCREEN IS WRONG | Complaint was distorted pix, found no pin correction.Servicer replaced shorted Q505, as well as L501, R571, and R518. Still hadno pin correction. While examining Q505 again, noticed that the boardsilkscreen is wrong, it shows L503 on base and D508 cathod | ||
| Sony | KV27AVR | RASTER REMAINS AFTER SET TURNED OFF. REPLACED Q402 | Raster stays on when power turned off intermittently. Found leaky transistor Q402 on A PC board. | ||
| Sony | KV2082ME7 | CHANNEL DISPLAY DOES NOT COME UP, REPLACED IC004 | Channel display does not come up. Discovered character generator IC does not run. | ||
| Sony | KV13VM21VC | TAPE STUCK, TICK NOISE WHEN UINT TURNED OFF,REPLACED D1822 | Set would make a ticking noise when off, replaced ZD1822 asper FPR, cured. Note: the Q1801 stand by regulator was not mounted toits heat sink If Q1801 got too hot due to no heat sink it could damageZD1822. Since it connects to its emitter. It would | ||
| Sony | KV13VM20 | TAPE JAMMED, REPLACED CAPSTAN MOTOR | Found capstan motor frozen. Jammed tape | ||
| Sony | KV13VM20 | TICK WHEN OFF AND AFTER GLOW, REPLACED D1822 | Replaced D1822 to cure tick noise. Added heat sink compoundto Q1801 it was not mounted. -SoLUTIOIN: D1822 corrects tick noise when off. Does Q1801 need to beheat sinked since it sits next to one? Its emitter connects to D1722which was bad. Is after |