Dicas Reparação
Modelo - Chassis 1000
Pesquisa: 1000 Enviar Dica Resolvida
Resultados 340
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | PIC1000 | NO SOUND, COLD SOLDER AT MICRO IC-1 | This unit had no sound. The expected high at pin 11 of IC401was missing as was its source at pin 110 of IC1 on the PU-90 board. | ||
| Sony | SLVR1000 | NO COLOR ON PLAYBACK | No color on playback, but on E-E is ok. SOLUTION : Found C422 loose solder on one leg, pushed up from underthe board by the plastic shield. | ||
| Sony | CVD1000 | A symptom of no picture in the pause mode was caused by amissing clock signal to ICs 657 and 658. This was caused by an open tracebetween those ICs and IC651 pin twelve, the clock source. | |||
| Sony | SPP1000 | LOW BATTERY AFTER CHARGING. | Customer states they have low battery after charging for longtime. | ||
| Sony | TAE1000ESD | REAR LEVEL LOW, INSUFFICIENT TO DRIVE AMP - FLASH HFP0040 | Customer is very dissatisfied with rear output level on hispre amp. I have verified that the rear channels are almost inaudible withall program materials. Customer owns following euqipment: TAE1000,TAN80ES, KEF10'S, FRONT SPEAKERS, CROWN PL4 W/KEF102 | ||
| Sony | PIC1000 | VERTICAL BAR ACROSS PASSWORD SCREEN WITH INCOMING CALLS | |||
| Sony | SLVR1000 | WILL STOP AFTER 4-5 SECONDS DURING AUDIO INSERT | The unit will stop few seconds after audio insert entered.Video insert ok. Video and audio insert not good. Normal record ok.Replaced IC503 no results. Disabled audio erase oscilator, unit did notstop. Assumed that the audio erase signal was fouling | ||
| Sony | TAM1000 | UNIT GRABS A LINE - REPLACE Q302, P/N 8-729-927-24 | When outside phone line is plugged into unit, unit will grab aline. This is caused by Q302 being shorted emitter to collector. Verysimilar to the problem with the TAM30/50 | ||
| Sony | SLV1000 | COLOR FLICKER | Missing C853 caused color to flicker on picture. | ||
| Sony | SLVR1000 | NO S VIDEO ON LINE 1 & 3 INPUTS | WHEN USING S VIDEO 1 & 3 INPUTS, NO S VIDEO OUT, BUT LINE 2 SVIDEO WORKED. | ||
| Sony | TAM1000 | UNIT CUTS OFF MESSAGES - RESOLDER IC803 | When playing back OGM, memo and ICM messages, unit will onlyplay half the message. Found a poor soldering job on IC803. This problemis found on several other units. | ||
| Sony | TAM1000 | NO POWER - RESOLDER IC102 | No LCD display. Plugged in power adaptor. Checked voltage atJ101 plug: +12V ok to IC102. Visual inspection on IC102: ground and outputof the voltage regulator were cold soldered. | ||
| Sony | TAM1000 | DISTORTED OGM & MEMO - REPLACE MIC301, P/N 1-542-161-11 | After recording OGM/Memo messages, playback is distorted.Replacing MIC301 fixes this problem. This problem has been found onseveral other units. | ||
| Sony | STRAV1000 | DEAD - REPLACED OPEN TRANSFORMER T801 | Traced problem to power transformer open primary. | ||
| Sony | SLHF1000 | WHEN POWERING ON UNIT CAPSTAND WOULDN'T STOP RUNNING | When pushing the power button, unit would power up but thecapstand motor wouldn't stop running. |