SHARP Service Mode (Modo de Serviço)

Insira Marca, Modelo ou Chassis.



Marca
Mod.
Ch.
Tipo
Modo
Proced.
File
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB 4. Press the MODE button on the remote control 5. 'SERV' will appear on the screen 6. Remove the jumper wire To select an adjustment use the channel up and down buttons To change the data press the data buttons The changes are stored automatically Turn the set off at the mains to exit the service mode.
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode - 'SERV' appears on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode - 'SERV' appears on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode