SHARP Service Mode (Modo de Serviço)
Marca
Mod.
Ch.
Tipo
Modo
Proced.
File
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video unit. Note that the wire is used just like a passing contact switch 5. 'SHARP Software Service Ver' will appear on the screen Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off To exit the service mode, press the standby button on the remote control.
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode - 'SERV' appears on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off
Sharp
CTV
Child Lock removal - pin no not known
PRESS VOL - ON TV & CHILD LOCK ON REMOTE TOGETHER , PRESS MODE ON REM, USING CHANNEL +/- TO SELECT CHILD LOCK , SELECT NEW PIN PRESS MODE E
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode - 'SERV' appears on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.
Universal LED TV Service Mode
Most universal led tv boards check:
- Menu → 1147
- Menu → 2580
- Source → 2580
All LED TV Service Codes
- Menu → 1147
- Menu → 1185
- Menu → 1183
- Menu → 2580
- Menu → 1187
- Menu → 7050
- Menu → 8202
- Menu → 7343
- Menu → 2008
- Menu → 1999
- Menu → 0000
- Menu → 1167
- Menu → 1199
- Menu → 1234
- Menu → 2387
- Menu → 8893
- Menu → 2383
- Menu → 4725
- Source → 3138
- Source → 2580
- Source → 2585
- Source → 7342
- Source → 2583
- Source → 2283
- Source → 2285
- Source → 3195
- Source → 3137
- Source → 0000