SHARP Service Mode (Modo de Serviço)

Sharp

CTV

Service Mode

1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.

Sharp

CTV

Service Mode

1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.

Sharp

CTV

Service Mode

1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Press the service switch again to exit the service mode

Sharp

CTV

Service Mode

1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode

Sharp

CTV

Service Mode

1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode

Sharp

CTV

Service Mode

1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode

Sharp

CTV

Service Mode

1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Press the service switch again to exit the service mode

Sharp

CTV

Service Mode

1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Press the service switch again to exit the service mode

Sharp

CTV

Service Mode

1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.

Sharp

CTV

Service Mode

1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode.