CHASSIS Service Mode (Modo de Serviço)

Grundig

LE

LCD

Service, Feature Mode

Premir i, aparece "User Menu" (Menu Utilizador), digitar 8500, para sair, premir novamente i

SCHNEIDER

TV8 chassis

CTV

Service Mode

Service-Mode Before being switched to the service mode the unit must be set to a channel with a test pattern. Note: The parameters are stored in changed. Press the red key and the blue key on the remote control simultaneously. Within 5 seconds, press the key P-and the key V+ on the local control panel simultaneously The title SERVICE Vxxx (xxx is for software version), appears in the screen. Keys P+ and P- (program) Call up tuning parameters Keys V+ and V- (volume) Modify tuning parameters Display Operation VP Adjust the vertical swift. HP Adjust the horizontal swift. VP Adjust the vertical picture height. Is the setting range not sufficient the range must change with the point CRT. VL Adjust top and button vertical linearity of screen centre. VB Adjust the intensity of the EHT. VB=24 PA Make vertical lines parallel with screen edge. HA Adjust the horizontal size. CC Adjust vertical lines in corners. Basic setting is 0. Setting should only be changed if PA balance cannot be adjusted satisfactorliy. PT Adjust values so that picture has same with at top and bottom edges or other vertical lines are parallel with each other. R Colour drive adjustment G Colour drive adjustment B Colour drive adjustment S-ADJ Connected a Test-picture with stereo signal to the tuner and adjust the TV. Connected Oscilloscope to Pin of ST601. Adjust to lowest crostalk between the channels. L-ADJ Connect Oscilloscope to Pin 1 of ST601. Connect a Test-picture (antenna level>60dBuV/75Ohm) with stereo signal (27kHz frequenceshift.54% modulation factor) to the tuner and adjust the TV. CRT Gear to vertical deflection. In dependence of the picture tube 0 or 1. GR/G+GL Shows like the Cutoff registration locks of in place. Its useable to adjust G2-adjustment. DELAY Superimpose the luma signal on the chrominance signal.

PHILIPS

A10E chassis

CTV

Service Mode

This model also supports the 062596 sequence followed by [i+]/[OSD]. Service default mode is entered using the 062596 sequence, followed by the - button on the TV set itself. Alternatively you can short-circuit pins 9261 and 9262 inside the set and then powering it up

PHILIPS

ANUBIS A chassis 2 local controls

CTV

Hotel Mode

Second Method Activation Select program 38, then press simultaneously "INSTALL" and "PROGRAM+" on local keyboard. De- Activation Select program 38, then press simultaneously "INSTALL" and "CONTROL" on local keyboard.

PHILIPS

G8.1 chassis

CTV

Hotel Mode

Activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "ON" De-activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "OFF"

PHILIPS

AA5 chassis

CTV

Hotel Mode

HOTEL MODE Activation Select program 38, press "MENU" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off -on the TV set. De-Activation Select program 38, then press "MENU" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. When de-activation is OK, a "H-" is displayed. To remove this display turn off -on the TV set.

PHILIPS

G8.1ECO chassis

CTV

Hotel Mode

Activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "ON" De-activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "OFF"

PHILIPS

G8 chassis

CTV

Hotel Mode

Activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "ON" De-activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "OFF"

PHILIPS

ANUBIS A chassis 8 local controls

CTV

Hotel Mode

Third Method Activation Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When activated "HOTEL MODE" a green "H" is displayed. To remove this display turn off-on the TV set. De-activation Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When de-activation is OK, a green "H" is displayed. To remove this display , turn off-on the TV set.

PHILIPS

ANUBIS A chassis 8 local controls

CTV

Hotel Mode

Second Method Activation Select program 38, then press simultaneously "INSTALL" and "PROGRAM+" on local keyboard. De-Activation Select program 38, then press simultaneously "INSTALL" and "CONTROL" on local keyboard.