Dicas Reparação
Modelo - Chassis SL5000
Pesquisa: SL5000 Enviar Dica Resolvida
Resultados 13
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | SL5000 | REPLACEMENT CAPSTAN MOTOR DOES NOT FIT | The original part number A-6737-103-A, which subs to 154149011as a replacement part, does not fit according to the servicer. He saysthe shaft is too short. Do you have any problems with this part? -HQ COMMENTS: No. This has been the replacement part | ||
| Sony | SL5000 | P/N FOR METAL PLATE | Need metal plate located beneath Ref. No. 105, Pg 4-3 of S/M. -HQ COMMENTS: I removed this part from a defective unit and have sentit to your attention. | ||
| Sony | SL5000 | TANTALUM CAPACITOR FAILURE | Upon installation of tantalum capacitor kit as per S/B #276C54 becomes leaky after about one week. This is the third such unit inabout one month that has done this. | ||
| Sony | SL5000 | BLUE LINE 1" FROM BOTTOM OF PICTURE DURING SELF-REC PLAYBACK | Pre-recorded tapes OK. Adjusted servo system - no help. -HQ COMMENTS: Please check Page 15 of SL-5000 Troubleshooting Guide(Servo Control - Picture not Normal at Self-Rec and Playback) and informof results. | ||
| Sony | SL5000 | NO THREADING | Threads part way, then stops. No slippage in idlers or belt.Motor DC still present when stalled. | ||
| Sony | SL5000 | INTERMITTENT SPEED ON BIII PLAYBACK | Tape speed intermittently changes on BIII playback. Unitrecords fine on BIII, BII and playback is good on BII. | ||
| Sony | SL5000 | DRUM OR CAPSTAN SERVO INSTABILITY | A large number of the 5000 series Betamax using the solidelectrolytic capacitors in servo circuits are having problem. The mostcommon failures are C007/C008/C010/C011/C016/C044/C050/C054/C063 on SS-9board. | ||
| Sony | SL5000 | NEED PART NUMBER FOR ANTENNA SWITCH UNIT | When ordering the antenna switch unit by P/N 9-982-040-00,customer keeps getting the antenna terminal strip. We need the currentnumber for the antenna switch unit. -HQ COMMENTS: The antenna switch is not available as a unit. Orderassy #306 P/N 1-464-1 | ||
| Sony | SL5000 | VIDEO NOISE DURING PB OF TIMER RECORDED TAPE | Customer brought in 4 tapes recorded on timer mode complainingof same problem. Recording made in FSC came out OK. Can you pleaseexamine enclosed sample and advise? -HQ COMMENTS: We confirmed the absence of the CTL signal on the sampletape. When the r | ||
| Sony | SL5000 | CAN | Sometimes ejects tape when PLAY is pushed. ANT SEL IN wouldchange logic when button pushed but that the output stayed high. Changingmicroprocessor produced no change. Pins 30, 31 and 29 all were high.Unsoldering these pins allowed the program select t | ||
| Sony | SL5000 | WRONG PART NUMBER IN S/M (SS-9 BD/C008) | Wrong part number in SL-5000 manual. | ||
| Sony | SL5000 | SLIPPAGE DURING THREADING/UNTHREADING CYCLES | Most threading problems are resolved by replacing belt,threading pulley and using sandpaper to rougher gear C surface. This gearis smooth and gets worse with use. -HQ COMMENTS: Roughing the surface with sandpaper and changing the Egear, belt and pulley | ||
| Sony | SL5000 | THREADING BELT SLIPPAGE CAUSING LOADING AND EJECT FAILURE | Failure to load or unload tape. |