Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CCDTR5 | NO REC ON CAMERA/CAUTION MODE IN FF- REPLACE CASSETTE HOLDER | Camera section cannot rec on VTR section, when you FF theunit will go into caution mode, found cassette holder bad. | ||
Sony | CCDTR5 | DARK PIX IN CAMERA/NO CHARACTER DISPLAY IN VF/CN802-VC60 | Unit has dark pix in e-e on camera section and no charactersyn. Found Cn802 on VC60 loose. | ||
Sony | CCDTR5 | NO AUDIO / REPLACE Q231 ON THE VS22 BD | No playback audio E-E ok. | ||
Sony | CCDTR5 | SWITCH BLOCK OFF STILL IN CAMERA MODE - Q621/VS-22 BD | unit came in with vtr/cam switch to off but still had e-e video.Tried swapping out switch block but that didn't fix the problem. I thenwent to the q603 and lifted the collector which shut down power. I put thepin back in then lifted the emitter -- s | ||
Sony | CCDTR5 | NO ZOOM (TELE OR WIDE)- Q703/LD-11 | unit came in with no zoom in both directions. there was nooutput to the zoom motor. going back to the zoom motor drive i found theinput ok but no output. taking dc measurements around this ic i foundpin#5 of ic701 low. following this back through | ||
Sony | CCDTR5 | NO SYNC AND LOW LUMINANCE IN PLAYBACK - C270/VS-22 BD | Unit came in with low or no luminance and no sync (In playback).Following Y signal up to ic203 pin#30 signal was bad. I then back-trackedto pin#31 which the signal was good there. Then going to q216 signal wasgood at both base and emitter. Going eve | ||
Sony | CCDTR55 | DISTORTED VIDEO TEARING PICTURE ON PLAYBACK AFTER RECORD | After recording, on playback picture is bending or tearingand video out level is low. | ||
Sony | CCDTR5 | NO MIC AUDIO/REPLACE C413 | Subbed MIC PCB to see if it was the problem. MIC PCBdefinitely had a probllme follwoing power to Q405, R415 which had 4.7v onobth sides. There was an open between R415 and base of Q405. C413 wasleaky which caused this trace to open up. | ||
Sony | CCDTR500 | NO COLOR IN E/E, WITH S-VIDEO INPUT. COMPOSITE VIDEO OK | No chroma appeared in VF, with S-Video external input. Colorwas present with composite input. | ||
Sony | CCDTR500 | NO VIDEO IN CAMERA/REPLACE IC662 | Found no video signal, output in camera VTR fine. Followedvideo signal up to IC662 which had an input signal at pins 49-56 but noouput at pin 25. Checked out IC found no clock at p ins 1/11. Replacedcrystal but stil no oscillation. Changed IC662, eve | ||
Sony | CCDTR500 | DIFFERENT IC602 | The service manual calls for 875234109 IC which is a CXD1256but the CXD1265R part 875235325 was in the unit. -HQ COMMENTS: The two ICs should be interchangeable. | ||
Sony | CCDTR500 | BATTERY END DETECT/CHANGE PAGE D ADDRESS 03 TO DATA 82 | Complaint: When fully charged battery and AC-V500 are hookedto camera, battery indicator will show 3/4/full charge, should show full. | ||
Sony | CCDTR5 | INTERMITTENT Y CAMERA/REPLACE C318 | Camera had intermit Y signal video would come and go byflexing board. | ||
Sony | CCDTR500 | NO VIEWFINDER PICTURE/REPLACE L370, DV12 BOARD | No viewfinder picture. Replacing open L370 corrected theproblem. -HQ COMMENTS: L370 passes the EVF 5V to the EVF assy. | ||
Sony | CCDTR500 | WON'T LOAD OR UNLOAD | The loading motor gear breaks loose from the drive shaft. |