Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
PHILIPS | ANUBIS A ANUBIS A | Não controla sintonia, brilho e contraste. | Microprocessador TMP47C434 (I.C. posição 7600) avariado. | SIMP | |
PHILIPS | ANUBIS A ANUBIS A | Esta TV não liga, mas faz um ruído na fonte | fiz medições e no B+ tem 5 volts. Ao retirar o transformador de linhas, o B+ ficou com 98 voltes. | Fiz a substituição do transformador de linhas, e a Tv ficou como nova | mauviciu |
PHILIPS | Chassis ANUBIS ANUBIS | Código Defeitos | Número de piscadas do LED: | 1- Problemas na RAM; 2- Problema no barramento DAS e SCL; 3- Alta corrente no feixe do TRC ; Proteção da varredura horizontal.4- Proteção da varredura vertical.5- Processador de áudio não responde ao microcontrolador;6- Erro de inicialização do BIMOS. 7- Erro geral no barramento I 2 C. 8- Erro geral I 2 C.9- Erro de configuração de EEPROM | |
Philips | Ch ANUBIS A | Fonte tem o "+95" com 100V mas Horiz. não arranca | Resist. 3444 5K6 2W >> 3W | ||
Philips | ANUBIS A | Low Contrast | C2448 47uF, 200v open circuit | ||
Philips | ANUBIS A-AC | Low 95v rail, 35v | C2530 open circuit completely | ||
Philips | ANUBIS-S | Video in sound at weak signed in PAL/SECAM sets | Modify in the BIMOS sound part: Replace C2102 by 4n7 (4822 126 12641) Replace C2112 by 560p (4822 126 13097) Replace C2119 by 270p (4822 126 13096) Replace C5112 by 15uH (4822 157 52224) REMARKS : Introduced in production week 9340 | ||
Philips | ANUBIS-S | Vertical shift alignment not enough | It is recommended to replace in the frame part of the 25" ANUBIS S BB: R3401 to 680R (4822 116 52228) nearby vertical shift potentiometer R3408. Realign the vertical shift after replacement. REMARKS : Introduced in production week 9405 | ||
Philips | ANUBIS-S | Vertical foldback lines | Replace R3325 on the CRT panel by 3k3 (4822 116 52269) Replace R3407 in the frame part of 20/21" by 33k (4822 051 10333) REMARKS : Introduced in production week 9318 | ||
Philips | ANUBIS-S | Spook on picture in all versions. | Replace IC7218 (voltage stabalizer of IC7225) by L7808CP (5322 209 86283). REMARKS : Introduced in production week 9333 (in Spanish service manual this is already updated in the spare parts list) | ||
Philips | ANUBIS-S | Sound plop at switching on/off spatial feature | It is recommended to solder a capacitor of 10uF 50V 20% 4822 124 40428 accross TS7140 (+ of capacitor at collector of TS7140 and - of capacitor at ground e.g. at jumper 9056) | ||
Philips | ANUBIS-S | Sound in picture (interference in picture) | In case of sound in picture interference it is recommended to: Place C2170 by 2n2 20% 50V 4822 126 12639 REMARKS : Introduced in production week 9407 | ||
Philips | ANUBIS-S | Sound in picture | Replace L5014 by 0.68uH (4822 157 63065) REMARKS : Introduced in production week 9319 | ||
Philips | ANUBIS-S | Sound distortion at theatre mode | To solve the problem make next changes: On incredible sound panel Pos. number Change to 1K2 4822 116 52207 3205,3405,3300,3303 Change to 100 nF 5322 121 42386 2302,2305 Change to 560E 4822 116 52226 | ||
Philips | ANUBIS-S | Sound distorted in theatre mode if volume is set from mid to highlevel | Modify following components on incredible sound panel. R3205 and R3405 into 1k5 - 4822 051 11502 C2302 and C2305 into 100nF - 5322 121 42386 R3305 and R3302 into 560E - 4822 050 15601 R3500 into 220E - 4822 052 10221 R3300 and R3303 into 1k2 - 4822 050 11 |