Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Philips | GFL2.20E 29PT828C | stuck in stby | resolder both ends of scan coils leads and resolder LOPTx | ||
Philips | GFL2.20E 29PT828C | sound int. goes low and distorted, rear speakers crackling | resolder earth links on component side of dolby module | ||
Philips | GFL2.20E 29PT828C | set trips from green LED to red, then back green to red | IC 7540/7550 TDA2616Q on audio PCB | ||
Philips | GFL2.20E 29PT828C | quiet buzz from centre speaker when playing back VCR via SCART | unclip the features board mounted behind the LOPTx on a plastic frame, turn through 180 degs and clip back into its frame (it works) | ||
Philips | GFL2.20E 29PT828C | no sound from front speakers in dolby or surround modes | go to install menu, then TV config menu and set "external amp" to off | ||
Philips | GFL2.20E 29PT828C | dead, LED flashing | Frame IC TDA8177 and C2260 100uF 63V | ||
Philips | GFL2.20E 29PT828C | dead, green LED flashing | R3148 120k gone high (large signal panel) | ||
Philips | GFL2.20E 29PT828C | dead | R3528 39k o/c | ||
Philips | 29PT9416 MG7.1 | Service Mode entering | Use the standard remote control and key in a special sequence '0,6,2,5,9,6' followed by pressing the 'MENU' button. If the main menu also appears with the service menu just press 'MENU' again to clear it.. The other way is to short the two service pins on the signal panel (pins 2 and 3 of connector 0356). The advantage of this last method is that all the software protections are turned off. | ||
Philips | 29PT9113C | WHITE BOX BOTTOM LEFT OF SCREEN | AUTO SUBTITLE SELECTED SWITCH OFF FROM HANDSET | ||
Philips | 29PT8444 | Correction to position 21 of styling 220 | Correction to position 21 of styling 220 of Product Survey 1999-3 (3122 785 10300 The code numbers mentioned for the aluminium columns at position 21 of styling 220 are not correct. The correct code numbers must be: 21 4822 466 12216 Aluminium colum | ||
Philips | 29PT8434 | Correction to position 21 of styling 220 | Correction to position 21 of styling 220 of Product Survey 1999-3 (3122 785 10300 The code numbers mentioned for the aluminium columns at position 21 of styling 220 are not correct. The correct code numbers must be: 21 4822 466 12216 Aluminium colum | ||
Philips | 29PT8424 | Correction to position 21 of styling 220 | Correction to position 21 of styling 220 of Product Survey 1999-3 (3122 785 10300 The code numbers mentioned for the aluminium columns at position 21 of styling 220 are not correct. The correct code numbers must be: 21 4822 466 12216 Aluminium colum | ||
Philips | 29PT8419 | Corrections on service manual EM1A AA | Page 4 Chapter 2: It was forgotten to mention here in this chapter that the architecture is 'hot'for a big part. E,g. deflection is 'hot', but also the middle big heatsink. So be warned. Page 16 Chapter 5: SAM-menu on right hand top side, sho | ||
Philips | 29PT8319 | Corrections on service manual EM1A AA | Page 4 Chapter 2: It was forgotten to mention here in this chapter that the architecture is 'hot'for a big part. E,g. deflection is 'hot', but also the middle big heatsink. So be warned. Page 16 Chapter 5: SAM-menu on right hand top side, sho |