Dicas Reparação
Modelo - Chassis
Pesquisa: Enviar Dica Resolvida
Resultados 81370
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | KPR4620 | DUST ON SCREEN, REPLACED SCREEN | Dust on screen. | ||
| Sony | EDC55 | LENS HOOD, LENS CAP AND GRIP BELT PART NUMBERS | The part numbers for the lens hood, lens cap and grip belt areas follows: Description Part Number Lens Hood 3-730-741-01 Lens Cap 3-730-742-01 Grip Belt 3-730-743-01 -HQ COMMENTS: A | ||
| Sony | FD35 | TUNING DIAL FOR FD-35A | Detroit SSC has received four cabinet assemblies (front) andthe tuner dial is missing. There is no part number for dial so I assumethis should be part of the cabinet. Could you please check into this?Thanks. -HQ COMMENTS: Tuning indicator is included | ||
| Sony | CDXA10 | CNP901 LINE OUT CABLE | Cannot identify part number for cable between Jack Board andMain Board. Two versions - older units (serial No. 17627) have a single8-pin connector for the Jack Board and dual 3-pin (5-pin connectors) forthe Main Board. Newer units (serial No. 22395) ha | ||
| Sony | CCDF30 | NO COLOR E-E IN CAMERA MODE | No color from camera section and line in. All other functionsworked properly. Found Q-360 not switching properly. It would not toggleIC-365 on IC-364. Camera 5V out of DC-DC converter was just low enough tokeep Q-362 on about 3.7VDC. This in turn wo | ||
| Sony | CCDV3 | NO CAMERA LUMINANCE | No luminance coming from camera section. Pin 36 of IC-801had no luminance signal, all DC voltages were correct and all signals toIC-801 were present - YH, B-Y, R-4 and YL-YH. Changed IC-801 still noluminance. | ||
| Sony | KV27SXR10 | LINE ACROSS TOP OF SCREEN, AG HOLDER, NO SOLUTION | The outside tech in Costa Mesa informed me of customerscomplaining about the three band that hold the aperture grille fromoscillating. The problem is the customer can see the top line from adistance of 7 to 8 feet. The tech has been out to four custome | ||
| Sony | CCDF30 | NO HORIZONTAL SYNC IN CAMERA POSITION | No horizontal sync in camera position. | ||
| Sony | GV8 | NOISY WHEN BREAKING | Noisy when breaking. Take-up-table gear teeth were worn out. | ||
| Sony | GV8 | NO VIDEO OUT FROM LINE | No video out, when line input is used, pin No. 8 on IC-701 isdead. | ||
| Sony | CDXR7 | COVER WILL NOT SNAP ONTO FRAME/MISSING INDENTATIONS | Cover (3-323-287-01) will not stay snapped onto frame(3-323-218-01). Frame does not have indentations like original to acceptand hold cover. -HQ COMMENTS: I am checking with Tokyo to see if there were two chassisand covers. | ||
| Sony | CDXA20 | D-509 WRONG ON NEW MCB JACK | CDX-A20 in for smashed MCB Jack and back. Replaced MCB andback. Noticed elevator ran slow. | ||
| Sony | EVS1 | UNIT ACCEPTS NO COMMANDS | Unit powers up but accepts no commands. FR-27 and TS-64circuit boards corroded. | ||
| Sony | KV1380R | NO PICTURE/WHITE LINES AT THE BOTTOM OF THE PICTURE, R552 | No picture, high voltage ok - white lines at the bottom ofthe picture. | ||
| Sony | SLV70HF | NO DRUM ROTATION | Unit loads tape capstan turns, but the drum does not. Thetape is then brought to the half loaded position and all commands aredisabled except eject. |