Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | MDP700 | DISC IS INTERMITTENTLY EJECTED | CD or LP intermittently ejects during or before play. | ||
Sony | SPP120 | PART NUMBER CLARIFICATION - REF #52 BUTTONS | Pictorial on page 42 gives the impression that if you orderNo. 52 you get all four buttons but you only get one. | ||
Sony | SPP170 | PART NUMBER CLARIFICATION - REF #52 BUTTONS | Pictorial on page 42 gives the impression that if you orderNo. 52 you get all four buttons but you only get one. | ||
Sony | SLHF860D | PART NUMBER FOR RECORD BUTTON | A Servicer here requires the record button for the abovemodel, but when he orders Ref. N0. 7 in the attached diagram, he onlyreceives the cover by itself. He needs a part number for the actualrecord slide button by itself. Can you please help? -HQ COM | ||
Sony | D99 | DISC SPINS BACKWARD | When disc is inserted and play button is pressed, disc startsto spin, stops and spins backward (counter clockwise). -HQ COMMENTS: The unit is a prototype with no model number, or serialnumber. This unit internally was very similar to a D-99. Using the | ||
Sony | KV32XBR15 | NO PICTURE AFTER REPLACING IC-102 (MEMORY CHIP) | After replacing IC-102 picture would blank. The same wouldoccur in the service mode. Thus, how do we adjust the unit if we can't seethe adjustments ? -HQ COMMENTS: Follow these simple steps: (Also see SB #99)1. Before replacing IC-102, chart down the ad | ||
Sony | SLVR5UC | CORRECT CLOCK ALIGNMENT PROCEDURE | Unable to perform mode control adjustment (page 22, step 1-8).What is shown is correct. Pin 8 of IC-201 is 4096hz, alignment says toset to .1249995 sec. (8hz). Procedure says buzzer will ring when junctionof R-109 and R-110 on the MF-101 board is short | ||
Sony | TCW31 | INCORRECT PART NUMBER | Part number listed in manual is not a valid number in system. | ||
Sony | STRVX550 | REPLACING LITHIUM BATTERY | When replacing bad and leaky back up batteries, while unsol-dering have had the molten solder disperse spraying solder on boards andoutwards to face, hands etc. This is due to the solderwick shorting anddischarging a capacitor across the solderwick. Th | ||
Sony | CCDV9 | LED WINDOW ON VIEWFINDER UPPER CABINET | We have a problem with the above part in stock in KC. Whenordered, the part does not include the small red LED window as shown inthe diagram, and there seems to be no seperate part number for the window.Can you please investigate and advise? -HQ COMMEN | ||
Sony | KV32XBR10 | IC-101 DOES NOT MATCH PART NUMBER IN MANUAL, TVP SB # 92 | Above part number does not match with the part called for inthe service manual. | ||
Sony | CDP570 | S/M ERROR; E-F BALANCE ADJUSTMENT | Page 7 of the S/M. E-F balance adjustment call for groundingTP(GND) to set adjustment mode. | ||
Sony | STRGX60ES | BIAS ADJUSMENT PROCEDURE IS INCORRECT | Noticed the bias adjustment was not correct in the Servicemanual. In the manual, it called to measure across R710(LF) & R760(RT).I believe you should measure from the emittrs of Q-704 & Q-703 for theleft channel and Q-754 and Q-755 on the right channel. | ||
Sony | STRGX50ES | BIAS ADJUSTMENT PROCEDURE IS INCORRECT | Noticed that the Bias adjust was not correct in servicemanual. In the manual it called to measure across R710(LF) & R760(RT).I believe you should measure form emitter of Q-704 and Q-703 for the leftchannel amd from the emitter of Q-754 and 755 on the ri | ||
Sony | KV32XBR15 | IC-101 DOES NOT MATCH PART NUMBER IN MANUAL, SEE SB # 92 | Above part number does not match with the part called for inthe service manual. -HQ COMMENTS: During production, the microprocessor was changed. Thesetwo ICs are not interchangeable. Please check to see what micro is beingused before ordering from KCP |