Dicas Reparação Thomson
Modelo - Chassis
Pesquisa: thomson
Resultados 130
Resultados 130
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Thomson | 32WF45E Chassi ICC20 | Desliga após 5Min de funcionamento imagem no OST/WEST com pequena ondelação leed fica a piscar 2 vezes e depois 5 infinitamente não volta a funcionar ligando novamente,só muito mais tarde. | Mudar o CL036 de 2;2Mf no circuito de Ost-West | ||
| Thomson | Chassis TX91G | Não Funciona - led frontal pisca em vermelho | Substituir Memoria 24C04 | ||
| THOMSON SABA | TX807VST = 418 | Não liga. Fonte chia | DL21 = BAV21 | ||
| THOMSON | Chassi TX807CS | Morto: Led não acende, fusível e transistor shoper não qeimam | Ver transistores TP022 e TP032 | ||
| THOMSON | ICC7 & ICC8 | Vertical - TDA8178FS em curto, já não se fabrica | Subs. por STV9379F, soldar Res 3K9 entre Pinos 2 e 7, soldar Zen. BZX75C2V1 Anodo Pino 7 Catodo Massa | ||
| THOMSON | 55MT16 | Não tem Som | TA02 | ||
| THOMSON | Chassis ICC9 | Perde a Syncro Linha e Trama | TH05 - TH04 - TX16 | ||
| THOMSON | Chassis ICC9 | Fica em Standby | TP66 e TP69 na Alimentação | ||
| THOMSON | 14MG10G | Tela azul com linhas de retorno | Transistor TT72/2SC2482 com fuga base/colector | ||
| Saba/Thomson | Chassi TX805 | Avaria do Zener DP50 | Verificar soldaduras do Pino 5 do TSL até ao electrolitico CP17 | ||
| Thomson | 24WK24U ICC17 | Set is tripping with flashing from the red standby light | Short the collector of TL71 to earth, if the set comes on you will find the frame chip is blown and ZL11 cp is o/c. If the set still wont come on them the LOPT is suspect | ||
| Thomson | TX91 | PLL will not lock for all frequencies keeps running during program search, on screen display moving / unstable | Changed the tuner and the STV8224 also check transistor at location TV02 is ok | ||
| Thomson | 28WR23EG ICC17 | AV1, AV2 are fine but AV3 do not work. Picture may be ok but no sound | Replace BA7604N, and check CX64 47pF | ||
| Thomson | ICC17 | Standby led fault codes and meanings list / standby led flashes then pauses | Code meanings are as follows: 10 = child lock mode, 11 = timer mode, 14 = there is no response from Iv01, 15 = there is no response from IS40, 20 = bus access prohibited by software, 21 = bus data line held low, 23 = bus clock line held low, 25 = switched 5v supply missing, 26 = crt is not warming in the allotted time, 27 = deflection failure more than three times, 28 = IF01 guard voltage pin 8 exceeded, 34 = no response from the nvm chip IR03, 36 = incorrect address passed to bus handler, 37 = unexpected level on NMI line power fail, 41 = bus data line not recoverable | ||
| Thomson | 28WS23E ICC17 | Set trips off int. Set tries to come on then goes back to standby | Dry joints on line o/p transformer |