Dicas Reparação
Modelo - Chassis
Pesquisa: Enviar Dica Resolvida
Resultados 81412
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CCDTRV21 | EJECTS AFTER TRYING TO LOAD (REF 771 WAS JAMMED ON REF 752) | After trying to load (with or without a tape) the unit wouldgo to eject mode. Problem was found to be caused by the pinch rollerassy, ref. 771, slipping over the base of the take-up guide assy., ref.752, causing these 2 parts to jam with each other. | ||
| Sony | CCDTRV21 | EATS TAPES (FOUND TG4, REF. 765, WAS BENT) | Unit would eat tapes. Found problem to be caused by TG4, ref.765, being bent. | ||
| Sony | CCDTRV21 | NO POWER IN CAM MODE (FOUND DD-80 CN003 LOOSE FROM VC-167) | Unit had no power in camera mode. Problem was caused by CN003of the DD-80 board which had come loose from the VC-167 board. | ||
| Sony | CCDTRV21 | NO MIC RECORD (FOUND MIC JACK WAS INTERMITTENT) | Unit would not record audio when an external mic was used.Problem was found to be caused by the mic jack, which was intermitent. | ||
| Sony | CCDTRV21 | LINES THROUGH PICTURE (FOUND POOR SOLDERING OF IC201) | Customer complaint was lines through picture found camerapicture wad distorted. Problem was found to be caused by IC201 on theVC-167 MCB, which was poorly soldered. IC201 is the Y/C processor. | ||
| Sony | CCDTRV21 | DEAD (FOUND LOOSE CONNECTIONS AROUND IC400) | Unit was dead. Problem was found to be caused by looseconnections around IC400 on the VC-167 MCB. | ||
| Sony | CCDTRV21 | NO LCD PICTURE (FOUND "PANEL OPEN" SWITCH S501 LOOSE) | There was no picture from the LCD panel. Problem was found tobe caused by S501 on the CF MCB being loose. | ||
| Sony | CCDTRV21 | NO EJECT (FOUND SOLDER BRIDGE ON FP249 SHORTING SENSOR H002) | Unit would not eject. Found problem to be caused by a solderbridge on FP-249 (below the takeup reel). The bridge shorted reelhall sensor H002, preventing any reel pulses from being generated. | ||
| Sony | CCDTRV21 | EATS TAPES (FOUND TENSION SPRING, REF. 781, HAD COME LOOSE) | Unit eats tapes. Found problem to be caused by tension spring,ref. 781, coming loose. | ||
| Sony | CCDTRV21 | EATS TAPES (FOUND TESNSION SPRING, REF. 783 HAD COME LOOSE) | Unit eats tape. Problem was found to be caused by tensionspring ref. 783, which had come loose. | ||
| Sony | CCDTRV21 | DEAD (FOUND POOR SOLDERING ON CN003 ON DD-80 MCB) | Unit was dead (would not even eject). Found problem to becaused by poor soldering of CN003 on the DD-80 MCB. | ||
| Sony | CCDTRV21 | EJECTS IMMEDIATELY AFTER LOADING (REF # 752 WAS DISLODGED) | Immediately after loading a tape, the unit would eject thetape. Found that the exit guide, ref. # 752, had come out of the track. | ||
| Sony | CCDTRV21 | NO EJECT (SCREW FROM JK146 MCB CAME LOOSE, JAMMED MECH) | Unit would not eject. Found screw from the JK146 MCB cameloose and jammed the mechanism. Screw was found relay gear ref. 812 andGL slider assy. ref. 820. | ||
| Sony | CCDTRV21 | WON'T LOAD TAPE (FOUND DRUM WOULD NOT ROTATE; REPLACED DRUM) | Unit would not load tape. Found that the drum had a tightspot which prevented it from rotating. | ||
| Sony | CCDTRV21 | DEAD (FOUND FP-220 NOT SEATED PROPERLY) | Unit was dead, but drew .32 amps no regardless of the mode. |