Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CDX4090 | CD SKIPS | CD Skips when playing. | ||
Sony | CDX4090 | UNIT HAS SKIPPING PROBLEM | CD Skips. | ||
Sony | CDX4090 | NO SOUND | No sound. | ||
Sony | CDX4090 | CD DOES NOT PLAY, DISPLAY READS E-04 | The LCD display of the unit reads E-04. This may be caused bythe CD making contact with the chucking arm (ref# 122). This may cause theCD not to spin and eventually displaying an error message. | ||
Sony | CDX4050 | CD DOES NOT PLAY, DISPLAY READS E-04 | The LCD display of the unit reads E-04. This may be caused bythe CD making contact with the chucking arm (ref# 122). This may cause theCD not to spin and eventually displaying an error message. | ||
Sony | CDTRV21 | POOR FOCUS ON EVF (FOUND FOCUS RING ON CRT MOUNTED POORLY) | The unit had poor focus on EVF. Found problem to be caused bythe focus ring being hot-glued to the CRT at an angle which preventedgood focus. This apparentlt occurred during manufacturing. | ||
Sony | CCDTRV21 | WASHED OUT PIX (FOUND IRIS STUCK OPEN, COLD SOLDER CN-101) | The picture was washed out. Found problem to be caused by astuck iris. Cold solder on CN101 of the CN-98 board resulted in the irisbeing stuck. | ||
Sony | CCDTRV21 | NO PIX IN EVF, ONLY VERTICAL LINE (FOUND BAD SOLDER ON L903) | EVF had no horizontal scanning, resulting in only a verticalline displayed. Problem was found to be caused by bad solder on L903 onthe VF-102 board. | ||
Sony | CCDTRV21 | DOOR WON'T CLOSE (MODE SWITCH BAD, MECH DID NOT EJECT FULLY) | Cassette door would not close, because the mechanism did notfully eject the last time the tape was ejected. Found problem to becaused by a faulty mode switch. | ||
Sony | CCDTRV21 | NO EJECT (FOUND TENSION REG. REF 833 WAS JAMMIMG LS CHASSIS) | The unit would not eject the tape. Found problem to be causedby the tension regulator plate which had come loose and was jamming the LSchassis. | ||
Sony | CCDTRV21 | NP FF OR REW (FOUND TEAR IN FP249) | The unit would not rewind or fast forward. Found problem tobe caused by unit not sensing movement of the supply reel. This wascaused by a bad conection on FP249, caused by some sort of contact with asharp edge. | ||
Sony | CCDTRV21 | NO ZOOM (FOUND TAB WHICH FOLLOWS WORM GEAR DISLODGED) | Lens would not zoom. After removing the zoom motor found thatthe inner tab which follows the worm gear on the motor shaft had twisted,preventing proper engagement with the worm gear. | ||
Sony | CCDTRV21 | DRUM IS UNUSUALY NOISY (TIGHTENED 3 SCREWS INSIDE OF DRUM) | Drum made rubbing noise while spinning. After removing thebottom plate of the drum assy, found the 3 inner screws loose. | ||
Sony | CCDTRV21 | NO COLOR IN REC, E-E OK, PRE-REC OK (FOUND X701 BAD) | Unit would not reord color. E-E color and playback ofpre-recorded tape color were OK. Found problem to be caused by X701 whichwas not put together properly. | ||
Sony | CCDTRV21 | INTERMITTENT NO POWER (FOUND COLD SOLDER ON J1 ON DD-80 MCB) | Unit was intermittently dead. Found problem to be caused bycold solder on J1 of the DD-80 MCB. |